NETGEAR Network Card WNDAP330 100NAS User Manual

b. Attach the three antennas to your  
wireless access point. The  
antennas are interchangeable and  
can be attached in any  
b. When prompted, enter admin for the  
user name and password for the  
)NSTALLATION 'UIDE  
password, both in lower case letters.  
WNDAP330 ProSafe 802.11n Dual Band Wireless Access Point  
A
The WNDAP330 user interface will  
display  
configuration.  
c. Connect an Ethernet cable from  
the WNDAP330 to the PC (point  
A in the illustration).  
c. Select Configuration > System >  
Basic > General from the menu and  
configure the Access Point Name and select the appropriate Country/Region of  
operation from the pull-down menu.  
Start Here  
Follow these instructions to set up your wireless access point. Before proceeding with the  
WNDAP330 installation, familiarize yourself with the contents of the Resource CD.  
Please refer to the Reference Manual on your Resource CD for instructions on advanced  
configuration options.  
d. Securely insert the other end of the  
cable into the WNDAP330  
Ethernet port (point B in the  
illustration).  
B
d. Select Configuration > IP > Basic from the menu and configure the IP settings  
for your network.  
e. Select Configuration > Wireless > Basic > Wireless Settings from the menu and  
configure the wireless interface for wireless access.  
Estimated Completion Time: 30 minutes.  
e. Connect the power adapter to the  
WNDAP330 and verify the  
following:  
Tip: Before mounting the WNDAP330 in a high location, first set up and test the  
WNDAP330 to verify wireless network connectivity.  
f. Then, select Configuration > Security > Basic from the menu and and click Edit  
to configure the level of data encryption security for your network.  
Power. The power light should be lit. If the power light is not lit, check the  
See the online help or the Reference Manual for full instructions. (A link to the  
online Reference Manual is on your Resource CD.)  
connections and check to see if the power outlet is controlled by a wall  
switch that is turned off.  
First, Verify the Package Contents  
Test. The test light blinks when the WNDAP330 is first turned on.  
3. Test Wireless Connectivity  
Unpack the box and verify the contents:  
LAN. The LAN light on the WNDAP330 should be lit (no light for a 10  
Mbps connection, amber for a 100 Mbps connection, and green for a 1000  
Mbps connection). If not, make sure the Ethernet cable is securely attached  
at both ends.  
Using a PC with a wireless adapter configured according to the wireless settings you  
just set in the WNDAP330, establish a wireless connection to the WNDAP330.  
WNDAP330 ProSafe 802.11n Dual Band Wireless Access Point  
Straight through Category 5 Ethernet cable  
Power adapter and cord (12V, 1.5A)  
Now that you have finished the setup steps, you are ready to deploy the WNDAP330  
in your network. If needed, you can now reconfigure the PC you used in step 1 back  
to its original TCP/IP settings.  
Wireless. The 802.11ng WLAN light should be lit.  
Three dual-band antennas: 2 dipole (long); 1 patch (square)  
Installation Guide  
2. Configure LAN and Wireless Access  
Resource CD which includes a link to the Reference Manual  
Warranty/Support Information Card  
Now, Deploy the WNDAP330  
a. From your PC, configure the WNDAP330 Ethernet port for LAN access.  
Connect to the WNDAP330 by opening your browser and entering  
http://192.168.0.235 in the address field.  
1. Disconnect the WNDAP330 and position it where you will deploy it. The best  
location is elevated, such as wall mounted or on the top of a cubicle, at the center of  
your wireless coverage area, and within line of sight of all the mobile devices.  
Then, Set Up the WNDAP330  
2. Position the antenna. Vertical positioning provides best side-to-side coverage.  
Horizontal positioning provides best top-to-bottom coverage.  
1. Connect the wireless access point to your computer.  
A login window will display.  
a. Prepare a PC with an Ethernet adapter. If this PC is already part of your network,  
record its TCP/IP configuration settings. Configure the PC with a static IP  
address of 192.168.0.210 and 255.255.255.0 as the subnet mask.  
3. Connect an Ethernet cable from your WNDAP330 Access Point to a LAN port on  
your router, switch, or hub.  
4. Connect the power adapter to the wireless access point and plug the power adapter in  
to a power outlet. The PWR, LAN, and Wireless LAN lights should light up.  
 

Miele Microwave Oven H4084BMSS User Manual
Miele Refrigerator KWT 1601 Vi User Manual
NETGEAR Network Card WN111v2 User Manual
NETGEAR Network Router WNR1000v3h2 User Manual
Nikon Camera Accessories iOS User Manual
NordicTrack Treadmill NTL118061 User Manual
Oki Printer ML420 User Manual
Palsonic CD Player DVD2080HD User Manual
Panasonic Cell Phone EB GD76 User Manual
Paradyne Network Router 6218 I1 User Manual