Napco Security Technologies Computer Hardware GEM RS232 User Manual

GEM-RS232  
R
Control Panel / Computer Converter  
INSTALLATION INSTRUCTIONS  
333 Bayview Avenue  
Amityville, New York 11701  
For Sales and Repairs, (800) 645-9445  
For Technical Service, (800) 645-9440  
© Napco 1999  
WI966 6/99  
GENERAL DESCRIPTION  
SYSTEM REQUIREMENTS  
The GEM-RS232 Control Panel/ Computer Converter is The following system hardware is required:  
an interface module which allows the NAPCO GEM-P9600  
·
·
Gemini GEM-P9600 Control Panel  
control panel to be connected to a computer which may be  
used to display system status. The GEM-RS232 is  
approved by Underwriters Laboratories for supplemental  
use only. It provides signal and ground isolation between  
the control panel and the computer and will protect the  
control panel from shorts, transients and surges which may  
emanate from the computer or the associated cabling.  
SE-AUTOMATION EPROM Upgrade must be  
installed in control panel.  
MOUNTING INSTRUCTIONS  
1
2
Open GEM-RS232 case using screwdriver.  
Drill hole in the center of the base of the case  
(side without label) using a 1/8” drill bit.  
The GEM-RS232 has been designed to be permanently  
mounted inside the cabinet of the GEM-P9600 and can be  
connected to the computer in several different fashions  
(see CONNECTION).  
3
4
Drill hole in housing using a 1/8” drill bit  
Mount securely using nut and screw provided  
CONNECTION  
·
Refer to the wiring diagram. Connect the 6-conductor  
SPECIFICATIONS  
Input Power: 12 V DC nominal, 60 mA (supplied by control  
panel connections)  
modular cable (supplied) to J1 (RJ12 style) of the  
control panel and then plug into the module (RJ12  
style) plug on the RS232 converter.  
·
Note: Reduce available panel combined auxiliary current  
by 60 mA)  
Dimensions: 11/16” x 2 9/16” x 2 9/16” (HxWxD)  
Range: 50 feet using RS232 serial cable  
100 feet using Cat5 cable  
·
For direct connection to serial port of computer or  
automation system, plug male DB9 connector of  
serial cable (NOT supplied) into the DB9 connector  
of the RS232 converter and connect other end to  
serial port of computer.  
ORDERING INFORMATION  
1. GEM-RS232  
·
·
·
RS232 Converter  
·
For CAT 5 wiring to computer or automation system,  
plug male DB9/CAT5 connector (supplied with  
GEM-RS232KIT) into the DB9 connector of the  
RS232 adapter and connect female DB9/CAT5  
connector (supplied with GEM-RS232KIT) to  
automation system DB9 connector. Use CAT5  
cable terminated with standard RJ45 connectors  
(not supplied).  
6 conductor Modular to Modular (RJ12 Style) cable  
1 SE-AUTOMATION EPROM  
2. GEM-RS232KIT  
·
·
·
·
RS232 Converter  
6 conductor Modular to Modular (RJ12 Style) cable  
8 Pin Modulator (RJ45 Style) to DB9 Male Adapter  
8 Pin Modulator (RJ45 Style) to DB9 Female  
Adapter  
·
1 SE-AUTOMATION EPROM  
NAPCO Security Systems, Inc.  
333 Bayview Avenue, Amityville, New York 11701  
For Sales and Repairs, call toll free: (800) 645-9445  
For direct line to Technical Service, call toll free: (800) 645-9440  
1
 

Miller Electric Welder and DS 74D16 User Manual
Milwaukee Nail Gun 54 43 0040 User Manual
MTD Lawn Mower 967K User Manual
National Instruments Network Card NI 9403 User Manual
New Buck Corporation Fan Heater Model 80 User Manual
Nintendo Computer Hardware GIC430F User Manual
Oki Printer 3320 User Manual
Olympus Camcorder SP 810UZ User Manual
Paradyne Modem 3811PLUS User Manual
Parasound Stereo Amplifier JC 2 User Manual