Table of Contents
C6100 Series Network User’s Guide
Table of Contents - 3
C6100 Series Network User’s Guide
Table of Contents - 4
Configuration
Introduction
The OkiLAN Internal Print Server is a fast 100BASE-TX/10BASE-T
network interface.
This network print server supports IEEE802.2, IEEE802.3,
Ethernet-II and SNAP and can detect those frame types
automatically.
Also, it supports major protocols such as TCP/IP, EtherTalk,
NetBEUI, Netware, Appletalk, and Rendezvous/Bonjour.
This section details the specification and several software utilities.
For multiple emulation printers, change the emulation in the
Printer Menu settings to Auto or PS before printing the
self-diagnostic test and settings.
C6100 Series Network User’s Guide
Configuration - 5
Specifications
CPU
Falcon
Frame types
IEEE 802.2
IEEE 802.3
Ethernet-II, SNAP, AUTO
100BASE-TX
10BASE-T
Network interface
Network protocols
TCP/IP
Network layer ARP, RARP, IP, ICMP, IPV6, UPnP,
AutoIP
Session layer TCP, UDP
Application layer LPR, FTP, TELNET, HTTP, IPP, BOOTP,
DHCP, SNMP, SMTP, NCP, SAP, NLSP, RIP, NDS, NDPS,
SPXII, Pure IP, SMP on TCP/IP, SMB on NetBEUI
IPX/SPX (NetWare)
Remote printer mode (up to eight file servers and 32
queues)
Print server mode (up to eight print servers)
Encrypted password supported in print server mode
SNMP
EtherTalk
ELAP, AARP, DDP, AEP, NBP, ZIP, RTMP, ATP
NetBEUI
SMB, NetBIOS
DDNS, WINS, Rendezvous/Bonjour
Self-diagnostic test printing
Banner supported
Functions
Monitoring/configure by Web browser
Printer status notification by E-Mail
C6100 Series Network User’s Guide
Configuration - 6
Self-diagnostic test
With the printer power switched on, press the print server test
button for more than three seconds and release. The
self-diagnostic test results and configuration settings are printed.
Printed self-diagnostic test sample
If “NG” is displayed instead of “OK” see the “Troubleshooting”
chapter.
C6100 Series Network User’s Guide
Configuration - 7
Printed configuration settings sample
networkinfo_pg1.jpg
C6100 Series Network User’s Guide
Configuration - 8
networkinfo_pg2.jpg
C6100 Series Network User’s Guide
Configuration - 9
Configuration Utility
Available utilities
You can configure the print server by using one of the following
methods:
Utility
Features
System requirements
Quick Setup
Configure the print server
easily and simply without
installing any software
packages into your system.
You can set the following:
Windows95/98/Me/NT4.0/
2000/XP (TCP/IP protocol or
IPX/SPX protocol should be
installed).
To create a NetWare queue,
NetWare Client 32 or
Enable/disable TCP/IP,
NetWare, EtherTalk, NetBEUI IntranetWare Client should
protocols. be installed in your system.
>
>
>
Set IP address, Subnet Mask
and Gateway for TCP/IP
manually or by using DHCP.
Set NetWare Mode and create
Queue/Print Server/Printer
objects.
Zone name and Port name for
EtherTalk.
Web browser
Configure the print server and Microsoft Internet Explorer
printer by using a Web
browser such as Microsoft
Version 3.0 and higher or
Netscape Navigator Version
Internet browser or Netscape 3.0 and higher. Operating
Navigator.
system that supports Web
browser.
AdminManager Configure the print server in
detail.
Windows95/98/Me/NT4.0/
2000/XP (TCP/IP protocol or
IPX/SPX protocol should be
installed). to create a
NetWare queue, NetWare
Client 32 or IntranetWare
Client should be installed in
your system.
TELNET
Configure the print server
using TELNET.
Third-party vendor developed
TELNET client package.
A TELNET Application is
standard in Windows/UNIX/
Linux.
C6100 Series Network User’s Guide
Configuration - 10
Utility
SNMP
Features
System requirements
The printer and print server
can be controlled using
third-party vendor developed
SNMP application.
Third-party vendor developed
SNMP application.
C6100 Series Network User’s Guide
Configuration - 11
Using Quick Setup
Quick Setup utility allows you to configure the print server easily
and simply without installing any software packages.
You can configure the following:
>
>
>
>
Enable/disable TCP/IP, NetWare, EtherTalk, NetBEUI
protocols.
Set IP address, Subnet Mask and Gateway for TCP/IP
manually or by using DHCP.
Set NetWare mode and create Queue/Print Server/Printer
objects.
Zone name and Port name for EtherTalk.
Configuration requires a PC with Windows 95/98/Me, Windows
2000 Advanced Server/Professional or Windows NT Server 4.0/
Work-station 4.0, Windows XP running TCP/IP or IPX/SPX
(NetWare).
This utility can only be used on a PC that can be connected to the
network with TCP/IP or IPX/ SPX.
This utility must be used on a PC that is located in the same
segment as the printer. To create a NetWare queue, NetWare
Client 32 or IntranetWare Client should be installed in your system.
The following explanation uses Windows 98 as an example.
1. Insert the CD-ROM provided with your printer into the
CD-ROM drive.
If the Menu Installer does not start automatically, click
Start→Run→Browse. Browse to your CD-ROM and click
Setup→Οpen→OK.
C6100 Series Network User’s Guide
Configuration - 12
2. Select [Optional Utilities]
netsofbutton.gif
3. Select [Install Quick Setup Utility].
install_configbut.gif
4. Select the language.
admgr_qsetbut.gif
sel_lang.gif
5. Select OKI Device Quick Setup.
sel_quicksetup.gif
6. Follow the on-screen instructions.
quicksetup.gif
C6100 Series Network User’s Guide
Configuration - 13
>
The NetWare Client 32 or IntranetWare Client should be
installed on the PC used for the creation of network queues.
Installation enables the user to create network queues and
perform other functions.
7. If the settings are correct, click [Execute]. The new settings
are transmitted to the network card but the network card is
still operating with pre-transmission settings.
8. Click [Finish] to validate the new settings. Depending on the
model, the printer may have to be switched off and on
again.
C6100 Series Network User’s Guide
Configuration - 14
Using a Web browser
If the print server is connected to the network using TCP/IP, its
settings and the printer menu settings can be configured using a
Web browser, such as Microsoft Internet Explorer Version 4.0 and
higher, or Netscape Navigator version 4.0 and higher. No
guarantees are offered for other browsers. Refer to the relevant
manuals for details of how to launch and use the browser.
The network addresses used in this manual are shown as examples
only. Network addresses used in your installation must be
generated from your own network. To apply configuration changes
using a Web browser, you will be prompted for a username and
password.The username is [root] and the default password is the
last six digits of the Ethernet address.
The following explanation uses Windows 95 and Microsoft Internet
Explorer version 4.0 as an example.
1. Configure the IP Address, Subnet Mask and Gateway for the
network card. Launch the Web browser, enter the IP Address
of the network interface card in [Address (Location/
Position)] and press the [Enter] key. The Printer Status
screen is displayed.
status.bmp
2. Click on a tab to see a particular Category, then click the
items you want to change in the left column. For more
details of corresponding items in WEB and TELNET
C6100 Series Network User’s Guide
Configuration - 15
equivalents, see the description in the Configurable Items
and Default Values table starting on page 50.
3. To ensure correct operation, follow the procedure below for
the appropriate network browser.
Microsoft Internet Explorer
a. Select [Internet Options] in the [Tools] menu.
b. Click on the [General] tab and click [Settings] in
[Temporary Internet files].
c. Select [Every visit to the page] in [Check for newer
versions of stored programs].
Netscape Navigator
a. Select [Settings] in the [Edit] menu
b. Click [Cache] in [Details].
c. Select [Once per session] in [Document in cache is
compared to document on network].
If you change the window size of the browser immediate-
ly after changing the configuration, [Security informa-
tion] may be displayed. Uncheck [Display this message
next time] in the dialogue.
4. After making changes, click [Submit].
5. Enter [root] in User name and your password (default is the
last six digits of the Ethernet address) in Password and click
[OK].
C6100 Series Network User’s Guide
Configuration - 16
6. After the new values are transmitted to the network card,
the following screen is displayed. If a different message is
displayed, check the settings.
ENTERPASSWORD.bmp
For example: For Ethernet address 00:80:92:01:00:D2, a default
password is [0100D2]. The Ethernet address (MAC address) is
displayed during the self-diagnostic test.
The root password can be changed to allow you to configure the
print server and printer by using a Web browser. The default
password is the last six digits of the MAC address.
To change the root password for configuration via a Web browser,
access [http://OKILAN IP address or hostname>/
system_password.htm]. After inputting the current root password,
this screen is displayed:
bmp21.bmp
Input a new root password in [New Admin Password] and [Confirm
New Admin Password] then select [Submit] button.
C6100 Series Network User’s Guide
Configuration - 17
The root password for configuration via Web browser is different for
AdminManager/TELNET/FTP. These passwords can be set in
AdminManager or TELNET.
C6100 Series Network User’s Guide
Configuration - 18
Standard Setup Using AdminManager
AdminManager is a powerful Microsoft Windows-based utility to
configure all print server functions by using a graphical user
interface.
Configuration requires a PC with Windows 95/98/Me, Windows
2000 Advanced Server/Professional or Windows NT Server 4.0/
Work-station 4.0, Windows XP running TCP/IP or IPX/SPX
(NetWare).
This utility can only be used on a PC that can be connected to the
network with TCP/IP or IPX/ SPX and must be used on a PC that is
located in the same segment as the printer.
To create a NetWare queue, NetWare Client 32 or IntranetWare
Client should be installed on to your system.
The following explanation uses Windows 98 as an example.
C6100 Series Network User’s Guide
Configuration - 19
Installation
The following explanation uses Windows 98 as an example.
1. Insert the CD-ROM provided with your printer into the
CD-ROM drive.
If the Menu Installer does not start automatically, click
Start→Run→Browse. Browse to your CD-ROM and click
Setup→Οpen→OK.
2. Select [Optional Utilities]
netsofbutton.gif
3. Select [Install Quick Setup Utility].
install_configbut.gif
4. Select the language.
sel_lang.gif
C6100 Series Network User’s Guide
Configuration - 20
5. Select OKI Device Standard Setup.
sel_quicksetup.gif
6. Follow the on-screen instructions. If you want to install
AdminManager on your local drive, select [Install and
Execute]. Otherwise, select [Execute from CD-ROM].
adminmgr_execute.bmp
C6100 Series Network User’s Guide
Configuration - 21
Status Menu
In the [Status] menu, the following items can be selected:
Item
Function
Printer Status
Current printer status is displayed:
bmp10.bmp
System Status
Displays current OkiLAN configuration.
Configuration data can be saved as log file.
bmp11.bmp
List of Configuration
Items
Displays current configuration. Configuration data
can be saved as log file.
bmp13.bmp
C6100 Series Network User’s Guide
Configuration - 23
Setup Menu
In this menu, the following items can be selected:
Item
Function
Oki Device Setup
Setup by HTTP
Configure the OkiLAN.
Launch the default browser in your environment to
access the selected printer’s web page.
Setup by TELNET
Launch TELNET application in your environment to
access the selected printer’s TELNET port.
Note: The TELNET application is not included as part of
the OkiLAN package. Install the TELNET package on to
your system. For further information, see your
Windows manual.
Create Netware
Queue
Create a NetWare queue.
Delete NetWare
Object
Delete NetWare object.
Reset
Reset the selected network interface card.
Print self-diagnostic test pages.
Test Print
IP Address Setup
Set static IP address of network interface card
manually.
C6100 Series Network User’s Guide
Configuration - 24
Oki Device Setup
In this section you can configure the print server. It contains
details for the following selectable tabs:
>
>
>
>
>
>
>
>
>
General
TCP/IP
Netware
EtherTalk
NetBEUI
SNMP
E-Mail (Send)
SMTP
Maintenance
The following section explains each tab’s functionality.
C6100 Series Network User’s Guide
Configuration - 25
General Tab
This allows you to set or change the root password used for Admin
Manager, TELNET and FTP.
bmp20.bmp
Location
Comments
Change root
password
You can set/change the root password for
AdminManager, TELNET and FTP.
bmp21.bmp
TCP/IP Tab
This allows you to configure TCP/IP related items.
bmp22.bmp
Location
Comments
Use TCP/IP
Protocol
Set TCP/IP protocol as enabled/disabled.
Use DHCP/BOOTP Check this item if IP address, subnet mask, default
gateway and IP addresses for DNS primary server and
secondary servers are retrieved from the DHCP or
BOOTP server. Otherwise, clear.
IP Address
Set the IP address of the selected network interface
card.
Subnet Mask
Default Gateway
Set the subnet mask of the selected network interface
card.
Set the default gateway of the selected network
interface card.
C6100 Series Network User’s Guide
Configuration - 26
Location
Comments
DNS Server . . .
Set IP addresses for DNS primary and secondary
servers, and allows you to use DDNS.
bmp23.bmp
Auto Discovery
WINS Server
Use Network PnP, use Bonjour, set Device Name.
Set Primary Server, Secondary Server, Scope ID.
To find corresponding items in WEB and TELNET, see the
equivalent in the Configurable Items and Default Values table that
C6100 Series Network User’s Guide
Configuration - 27
Netware Tab
This is where you can configure NetWare related items.
bmp24.bmp
Location
Comments
Use NetWare Protocol
Print Server Name
Frame Type
Set NetWare protocol as enabled/disabled.
Set Print Server name.
Set primary NetWare frame type.
Set NetWare mode.
Operation Mode
Check box besides
Bindery Setup
Check if you want to use the Bindery mode and
Bindery Setup button becomes available. If it is
unchecked, the button is greyed out.
C6100 Series Network User’s Guide
Configuration - 28
Location
Comments
Bindery Setup
Configure items related to Bindery mode.
bmp25.bmp
In this dialogue box, the following items can be
configured.
Available File Server
and Selected File
Server.
Select file servers to
connect. Up to eight file
servers can be
selected. Select a
server from Available
file server list and click
>>. The server is
copied to Selected file
server box.
Password.
Set password for Print
Server.
Job Polling Time.
Set print job polling
interval in seconds.
NDS Setup
Set NDS tree and context where Print Server was
created.
bmp26.bmp
C6100 Series Network User’s Guide
Configuration - 29
Location
Comments
RPRINTER Setup
Available if you select RPRINTER mode in
Operation Mode.
mp27.bmp
By selecting the [RPRINTER] button, this is
displayed:
bmp28.bmp
NDS or Bindery
Show the Available
print server tree in NDS
mode or Bindery mode.
Available print server
and Selected print
server
Select file servers to
connect. Up to eight file
servers can be
selected. Select a
server from Available
file server list and click
>>. The server is
copied to Selected file
server box.
Time Out
Set duration from the
last data’s arrival to
freeing of the port in
seconds.
Printer Name
Set the NetWare printer object name.
C6100 Series Network User’s Guide
Configuration - 30
EtherTalk Tab
This allows you to configure EtherTalk related items.
bmp29_a.bmp
Location
Comments
Use EtherTalk
Protocol
Set EtherTalk protocol to enabled/disabled.
Printer Name
Zone Name
Set EtherTalk Printer object name.
Set the zone name to which the OkiLAN belongs.
NetBEUI Tab
This allows you to configure NetBEUI related items.
bmp30.bmp
Location
Comments
Use NetBEUI
Protocol
Set NetBEUI protocol to enabled/disabled.
Short Printer Name Set a computer name for the OkiLAN.
Workgroup
Comment
Set a work group name to which the OkiLAN belongs.
Set the comments for the OkiLAN.
C6100 Series Network User’s Guide
Configuration - 31
SNMP Tab
This allows you to configure SNMP related items.
bmp31.bmp
Location
Comments
SNMPv1
Settings
Community names: SNMP Write Community, SNMP Read
Community.
SysContact
SysName
Set SysContact (printer manager) name.
Set SysName (printer model name).
SysLocation
Set SysLocation (the location where the printer is
installed).
C6100 Series Network User’s Guide
Configuration - 32
Location
Comments
Printer Trap
Setup . . .
By selecting the button, the following dialogue box is
displayed:
bmp32.bmp
In the dialogue box, the following items can be
configured:
Printer Trap
This community name is assigned to
Community Name outgoing printer status traps such as
off-line, paper out, etc.
TCP#1—5
Detail . . .
Set the IP address to which a Trap
packet will be sent. You can set up to
five IP addresses.
By selecting the Detail button, the
following items can be configured:
Trap Enable
Set sending a Trap
packet, enabled or
disabled, for each
destination.
Printer Reboot
Receive Illegal
Set sending a Trap,
enabled or
disabled, when the
printer restarts.
Set sending a Trap,
enabled or
disabled, when
illegal data is
received.
On-Line
Off-Line
Paper Out
Set sending a Trap,
enabled or
disabled, when the
printer turns to
On-Line.
Set sending a Trap,
enabled or
disabled, when the
printer turns to
Off-Line.
Set sending a Trap,
enabled or
disabled, when
paper is out.
C6100 Series Network User’s Guide
Configuration - 33
Location
Comments
Detail . . .
Printer Trap
Setup . . .
Cover Open
Printer Error
Set sending a Trap,
enabled or
disabled, when the
printer cover
opens.
Set sending a Trap,
enabled or
disabled, when any
errors occur.
IPX
Set node address and network address
to which a Trap packet will be sent.
Detail . . .
By selecting the Detail button, the
following items can be configured:
Trap Enable
Set sending a Trap
packet, enabled or
disabled, for each
destination.
Printer Reboot
Receive Illegal
Set sending a Trap,
enabled or
disabled, when the
printer restarts.
Set sending a Trap,
enabled or
disabled, when
illegal data is
received.
On-line
Off-line
Set sending a Trap,
enabled or
disabled, when the
printer turns to
On-Line.
Set sending a Trap,
enabled or
disabled, when the
printer turns to
Off-Line.
Paper Out
Paper Jam
Set sending a Trap,
enabled or
disabled, when
paper is out.
Set sending a Trap,
enabled or
disabled, when a
paper jam occurs.
C6100 Series Network User’s Guide
Configuration - 34
Location
Comments
Detail . . .
Printer Trap
Setup . . .
Cover Open
Printer Error
Set sending a Trap,
enabled or
disabled, when the
printer cover
opens.
Set sending a Trap,
enabled or
disabled, when any
errors occur.
C6100 Series Network User’s Guide
Configuration - 35
E-Mail (Send) Tab
In E-Mail Tab, you can configure SMTP related items.
bmp34.bmp
Location
Comments
Use SMTP
Set sending E-mail via SMTP, enabled or disabled.
Transmit Protocol
SMTP Server
Name
Set Server name.
Priinter E-mail
Address
Set the E-mail address that is used in the [From] field in
the mail header.
Destination
Address 1 - 5
Set E-mail addresses to where E-mail should be send.
Up to five E-Mail addresses can be set.
Set Notify Mode.
Set Event Mode.
Attach Info
Authentication
Comments
Others
Set information to attach.
Set User ID and Password.
Add comments
Set SMTP port number and Reply-To address
C6100 Series Network User’s Guide
Configuration - 36
SMTP Tab
In SMTP Tab, you can configure SMTP related items.
Location
Comments
Use SMTP
Set sending E-mail via SMTP, enabled or disabled.
Transmit Protocol
NTP Server 1
Address
Set Server 1 address.
Set Server 2 address.
NTP Server 2
Address
Adjust Interval
Set interval that OkiLAN checks specified events: 1, 12,
or 24 hours.
Local Time Zone Set time.
Daylight Saving
Set Daylight Saving time.
bmp34.bmp
C6100 Series Network User’s Guide
Configuration - 37
Maintenance Tab
In Maintenance Tab, you can configure the following:
Location
Comments
LAN Scale
Set LAN Scale (normal/small)
IP Filter Setup
Detail...
By selecting the button, the
following items can be configured:
Configuration
Admin IP address
IP Address Range
Start/End
Address
Printing
Service
Detail...
By selecting the button, you can
setup the following service:
Use TCP/IP Protocol
Use NetBEUI Protocol
Use FTP Service
UseTelnet Service
Use Web Service
Use IPP Service
Use SNMP Service
Use SMTP Transmit
Use encrypted communidation for
configuration data
C6100 Series Network User’s Guide
Configuration - 38
IP Address Setup
If you only use TCP/IP and the OkiLAN has not yet been configured,
occasionally it may not be displayed on AdminManager. You can
configure the IP address of the OkiLAN by this function.
1. Select [IP Address Setup] from the [Setup] menu.
2. Set [Ethernet Address] and [IP Address] and select [OK].
bmp42.bmp
>
The Ethernet Address (MAC address) is displayed during the
self-diagnostic test.
3. AdminManager asks whether you want to initialize the
network interface card or not. Select [Yes]. Even if you
select [No] here, the IP address that you set can be used
after turning the printer OFF and ON. The requirement to
turn your printer OFF and ON is dependent on the network
interface card.
C6100 Series Network User’s Guide
Configuration - 39
Option Menu
In the [Option] menu, the following item can be selected:
Item
Function
Use TCP/IP
Protocol
If this item is selected, AdminManager uses TCP/IP
protocol to search/configure network interface cards.
Use IPX/SPX
Protocol
If this item is selected, AdminManager uses IPX/SPX
protocol to search/configure network interface cards.
Environment
Setup
TCP/IP Tab
bmp50.bmp
Set broadcast addresses that are
used to search OKI network interface
cards using the TCP/IP protocol. If
[Use TCP/IP protocol] is unchecked,
the search will not be carried out
using TCP/IP.
NetWare Tab
bmp51.bmp
Set network addresses that are used
to search OKI network interface cards
via NetWare protocol. If there any
many NetWare file servers on your
network, specify the network address
to which the network card belongs. If
[Use NetWare protocol] is unchecked,
the search will not be carried out
using NetWare, but if [Auto Search] is
selected, AdminManager will search
all networks that AdminManager can
detect.
SNMP Tab
Obtain the printer name via SNMP;
Set Community Name.
TimeOut Tab
[Search Every]: Set response waiting
time from a network card in seconds.
bmp52.bmp
[Time Out]: Set time out between
AdminManager and the network
interface card in seconds.
[Retry]: Set how many times the
retry will be carried out between
AdminManager and the network
interface card.
C6100 Series Network User’s Guide
Configuration - 40
Using TELNET
The OkiLAN can be configured using TELNET. TELNET requires the
OkiLAN to have a valid IP address configured. If the NIC already
has an IP address configured, skip steps one to three below.
>
Note: Please ensure that a valid IP address for you network
environment is used. Use of an incorrect IP address can cause
serious problems on your network.
The following explanation uses Sun Solaris 2.4 as an example. The
method of configuring commands may differ between
workstations. Refer to the workstation’s manual.
1. Login as [root].
If you do not have Superuser rights, the network manager should
run the configuration.
2. Set a temporary IP Address on the NIC using the ARP
command.
Example: for IP address 172.168.20.127 and network card address
00:80:92:01:00:D2
# arp –s 172.168.20.127 00:80:92:01:00:D2 temp
The Ethernet address (MAC address) is displayed during the
self-diagnostic test. A temporary address does not need to be set
if an IP address has already been set.
3. Use the PING command to confirm the connection with the
network card.
Example: for IP address 172.168.20.127
# ping 172.168.20.127
If there is no reply, there is a problem with the configuration of the
IP address (the IP address has been already set manually or by the
C6100 Series Network User’s Guide
Configuration - 42
DHCP/RARP server), or with the network. Reset the network
interface card settings to default and try to set temporary IP
address. If you still have the problem after resetting the network
interface card, consult the network manager.
4. Login to the network card using TELNET.
Example: for IP address 172.168.20.127
$ telnet 172.168.20.127
Trying 172.168.20.127
Connected to 172.168.20.127
Escape character is ‘^]’.
EthernetBoard OkiLAN PRINTER".
login: root
‘root’ user needs password to login.
password:
User ‘root’ logged in.
No. Message Value (level.1)
------------------------------------
1: Setup TCP/IP
2: Setup SNMP
3: Setup NetWare
4: Setup EtherTalk
5: Setup NetBEUI
6: Setup printer port
7: Display Status
C6100 Series Network User’s Guide
Configuration - 43
8: Setup printer trap
9: Setup SMTP (E-Mail)
97: Reset to factory set
98: Quit setup
99: Exit setup
Please select (1-99)?
5. Enter the number of the items to be changed and the details
screen for that item is displayed. The menu has the
following hierarchical structure so for more details see the
description in the appropriate numbers
C6100 Series Network User’s Guide
Configuration - 44
Telnet hierarchical structure
Level1
Level2
Level3
Ref No.
1: Setup TCP/IP
1: TCP/IP protocol
2: IP address
3: Subnet
TCPIP-1
TCPIP-2
TCPIP-3
TCPIP-4
TCPIP-5
TCPIP-6
—
—
—
—
—
—
4: Gateway
5: RARP protocol
6: DHCP/BOOTP
protocol
7: DNS server(Pri.)
8: DNS server(Sec.)
9: Root password
TCPIP-7
TCPIP-8
TCPIP-9
—
—
—
—
—
—
99: Back to prior menu
2: Setup SNMP
1: Authentic
community
SNMP-1
2: Trap community
3: Trap address
4: SysContact
SNMP-2
SNMP-3
SNMP-4
SNMP-5
SNMP-6
SNMP-7
SNMP-8
—
—
—
—
—
—
—
—
—
5: SysName
6: SysLocation
7: DefaultTTL
8: EnableAuthenTrap
99: Back to prior menu
C6100 Series Network User’s Guide
Configuration - 45
Level1
Level2
Level3
Ref No.
3: Setup NetWare
1: NetWare protocol
2: Packet type
NetWare-1
NetWare-2
NetWare-3
NetWare-3
NetWare-4
NetWare-4
NetWare-4
NetWare-4
NetWare-4
NetWare-4
NetWare-4
NetWare-5
NetWare-6
NetWare-7
NetWare-8
NetWare-9
NetWare-10
—
—
—
3: NetWare mode
—
4: Setup PSERVER
mode
1: FSERVER name 1
2: FSERVER name 2
3: FSERVER name 3
4: FSERVER name 4
5: FSERVER name 5
6: FSERVER name 6
7: FSERVER name 7
8: FSERVER name 8
9: Machine name
10: Password
11: Job polling interval
12: Bindery mode
13: NDS tree
14: NDS context
99: Back to prior menu
1: PSERVER name 1
2: PSERVER name 2
3: PSERVER name 3
4: PSERVER name 4
5: PSERVER name 5
6: PSERVER name 6
7: PSERVER name 7
8: PSERVER name 8
9: Job timeout
3:Setup Netware
5: Setup RPRINTER
mode
NetWare-11
NetWare-11
NetWare-11
NetWare-11
NetWare-11
NetWare-11
NetWare-11
NetWare-11
NetWare-12
—
99:Back to prior menu
99: Back to prior menu —
—
4: Setup EtherTalk
5: Setup NetBEUI
1: EtherTalk protocol
2: Zone name
—
—
—
—
—
—
—
EtherTalk-1
EtherTalk-2
—
99: Back to prior menu
1: NetBEUI protocol
2: Computer name
3: Workgroup name
4: Comment
NetBEUI-1
NetBEUI-2
NetBEUI-3
NetBEUI-4
—
99: Back to prior menu —
C6100 Series Network User’s Guide
Configuration - 46
Level1
Level2
Level3
Ref No.
6: Setup printer
port
1: NetWare port name
2: EtherTalk port name
3: BOJ string
—
—
—
—
—
—
—
—
—
—
Port-1
Port-2
Port-3
Port-4
Port-5
Port-6
Port-7
Port-8
Port-9
Port-10
Port-11
—
4: EOJ string
5: BOJ string(KANJI)
6: EOJ string(KANJI)
7: Printer type
8: TAB size (char.)
9: Page width (char.)
10: Page length(line)
11: lpr/ftp banner
—
99: Back to prior menu —
7: Display status
1: prn1
—
—
—
STATUS-1
STATUS-2
Trap-1
2: system
8: Setup printer
trap
1: Prn-Trap community
2: Setup TCP#1 trap
3: Setup TCP#2 trap
4: Setup TCP#3 trap
5: Setup TCP#4 trap
1: TCP#1—5 Trap enable Trap-2
2: On-line trap
Trap-3
Trap-4
Trap-5
Trap-6
Trap-7
Trap-8
Trap-9
3: Off-line trap
4: Paper Out trap
5: Paper Jam trap
6: Cover Open trap
7: Printer Error trap
8: TCP#1—5 Trap
address
99: Back to prior menu
1: IPX Trap enable
2: On-line trap
—
7: Setup IPX trap
Trap-10
Trap-11
Trap-12
Trap-13
Trap-14
Trap-15
Trap-16
Trap-17
Trap-18
—
3: Off-line trap
4: Paper Out trap
5: Paper Jam trap
6: Cover Open trap
7: Printer Error trap
8: IPX Trap address
9: IPX Trap net
99: Back to prior menu
99: Back to prior menu —
—
C6100 Series Network User’s Guide
Configuration - 47
Level1
Level2
Level3
Ref No.
9: Setup SMTP
(E-Mail)
1: SMTP Transmit
2: SMTP Receive
—
SMTP-1
SMTP-2
SMTP-3
SMTP-4
SMTP-5
SMTP-6
SMTP-7
SMTP-8
SMTP-9
—
3: SMTP server name
4: SMTP port number
5: E-Mail address
6: Reply-to address
—
—
—
—
7: Event to address 1
8: Event to address 2
9: Event to address 3
10: Event to address 4
11: Event to address 5
1: To Address 1—5
2: Re-send Interval
3: Off-Line
4: Consumable Message SMTP-10
5: Toner Low/Out
6: Paper Low/Out
7: Paper Jam
SMTP-11
SMTP-12
SMTP-13
SMTP-14
SMTP-15
SMTP-16
SMTP-17
SMTP-18
SMTP-19
—
8: Cover Open
9: Stacker Error
10: Mass Storage Error
11: Recoverable Error
12: Service Call Req.
13: Finisher
99: Back to prior menu
—
9: Setup SMTP
(E-Mail)
12: Signature line 1
13: Signature line 2
14: Signature line 3
15: Signature line 4
SMTP-20
99: Back to prior menu
1: POP3 protocol
—
—
—
—
—
—
—
10: Setup POP
(E-Mail)
POP-1
POP-2
POP-3
POP-4
POP-5
2: POP3 server
3: POP port number
4: POP3 server UserID
5: POP3 server
Password
6: Use APOP
POP-6
POP-7
—
—
7: Retrieve every
(min.)
99: Back to prior menu
—
—
—
—
97: Reset to factory
set
ETC-1
98: Quit setup
99: Exit setup
—
—
—
—
—
—
8. When configuration is complete, select [Exit Setup] to save
your change. To exit without saving your modification, select
[Quit].
C6100 Series Network User’s Guide
Configuration - 48
9. Turn the printer off and on again.
The network card continues to use pre-transmission settings until
the printer is turned off and back on again.
C6100 Series Network User’s Guide
Configuration - 49
Using SNMP
The printer and network card can be managed via a standard SNMP
management station. The network card supports SNMPv1, MIB-II
and OKI Data Private MIB.
The printer’s trap address can be set in five places using TCP/IP
and in one place with IPX.
The printer’s trap address can be set in five places using TCP/IP
and in one place with IPX.
Printer trap settings can be made with TELNET and a Web browser.
Configurable items and Default Values
Bold is the default setting.
Ref. No.
Admin
Manager
Web browser
TELNET/
Diagnostic
test print
Available
options
Notes
TCPIP-1
[OKI Device [Network
[Setup TCP/
ENABLE/
DISABLE
Set TCP/IP
protocol,
enabled/
disabled
Setup]-
Configuration]-[ IP]-
General
[TCP/IP]-
[Use TCP/IP
Protocol]
[TCP/IP
protocol]
Settings]-[Protoc
ol Options]-[TCP/
IP]
TCPIP-2
TCPIP-3
TCPIP-4
[OKI Device [Network
[Setup TCP/
0.0.0.0—
Set IP
Setup]-
Configuration]-[T IP]-[IP addres 255.255.255.25 address
CP/IP]-[Fixed IP s]
Address
Settings]-[IP
Address]
5 (0.0.0.0)
[TCP/IP]-
[IP Address]
[OKI Device [Network
[Setup TCP/
0.0.0.0—
Set subnet
Setup]-
[TCP/
IP]-[Subnet
Mask]
Configuration]-[T IP]-[Subnet
CP/IP]-[Fixed IP mask]
Address
Settings]-[Subne
t Mask]
255.255.255.25 mask
5 (0.0.0.0)
[OKI Device [Network
[Setup TCP/
0.0.0.0—
Set
Setup]-
[TCP/
IP]-[Default
Gateway]
Configuration]-[T IP]-[Gateway 255.255.255.25 gateway
CP/IP]-[Fixed IP address]
Address
Settings]-[Defaul
t Gateway]
5 (0.0.0.0)
(default
route).
C6100 Series Network User’s Guide
Configuration - 50
Ref. No.
Admin
Manager
Web browser
TELNET/
Diagnostic
test print
Available
options
Notes
TCPIP-5
[OKI Device [Network
[Setup TCP/
ENABLE/
DISABLE
SET RARP
function,
enabled/
disabled
Setup]-
[TCP/IP]-
[Use RARP]
Configuration]-[T IP]-[RARP
CP/IP]-[Method protocol]
for assigning IP
Address]-[RARP]
TCPIP-6
TCPIP-7
[OKI Device [Network
[Setup TCP/
ENABLE/
Set DHCP
function,
enabled/
disabled
Setup]-[TCP Configuration]-[T IP]-[DHCP/
DISABLE
/IP]-[Use
DHCP/
BOOTP]
CP/IP]-[Method BOOTP
protocol]
for assigning IP
Address]-[DHCP/
BOOTP]
[OKI Device [Network
[Setup TCP/
0.0.0.0—
Set IP
Setup]-
[TCP/IP]-
[DNS
Server...]
-[Primary
Server]
Configuration]-[T IP]-
CP/IP]-[Fixed IP
Address
Settings]-[DNS
Server Address
(Pri.)]
255.255.255.25 address for
5 (0.0.0.0)
primary
DNS server
[DNS
server(Pri.)]
TCPIP-8
[OKI Device [Network
[Setup TCP/
0.0.0.0—
Set IP
Setup]
Configuration]-[T IP]-[DNS
255.255.255.25 address for
CP/IP]-[Fixed IP server(Sec.)] 5 (0.0.0.0)
secondary
DNS server
-[TCP/IP]-
[DNS
Server...]
-[Secondary
Server]
Address
Settings]-[DNS
Server Address
(Sec.)]
TCPIP-9
SNMP-1
[OKI Device
Setup]-[Gen
eral]-[Chan
ge root
[Setup TCP/
IP]-
[root
password]
Any
Set the root
password of
OkiLAN
alphanumeric
characters up
to seven
characters.
(Default is null)
password]
[OKI Device [Network
Setup]-[SN Configuration]-[ SNMP]-[Authe alphanumeric
MP]-[Authe SNMP Traps]-
ntic
Community]
[Setup
Any
This
community
ntic
community]
characters up to name is
15 characters.
(Default is
[public])
used to
check
whether
incoming
SNMP
[MIB-II
Information]-[Au
thentic
Community]
requests
have the
correct
community
name or
not. The
community
name is
displayed
as ******
for security
reasons
C6100 Series Network User’s Guide
Configuration - 51
Ref. No.
Admin
Manager
Web browser
TELNET/
Diagnostic
test print
Available
options
Notes
SNMP-2
[OKI Device [Network
[Setup SNMP]- Any
This
community
Setup]-[SN Configuration]-[
MP]-[TRAP SNMP Traps]-
alphanumeric
characters up to name is
[Trap
community]
Community]
15 characters.
(Default is
[public])
assigned to
outgoing
system
traps such
as cold
start,
[MIB-II
Information]-
[Trap
Community]
authenti-ca
tion failure,
etc.
SNMP-3
SNMP-4
[OKI Device [Network
Setup]-[SN Configuration]-[
[Setup SNMP]- 0.0.0.0—
Set a
255.255.255.25 destination
5 (0.0.0.0)
[Trap address]
MP]-
[TRAP
Address]
SNMP Traps]-
[MIB-II
Information]-
[Trap IP Address]
IP address
of Trap
packet. If
0.0.0.0 is
set, Trap is
disabled
[OKI Device [Network
Setup]-[SN Configuration]-[ SNMP]-[SysCo alphanumeric
[Setup
Any
Set
SysContact
MP]-[SysCo General
ntact]
characters up to (printer
ntact]
Settings]-[Syste
255 characters. manager)
m
(Default is null) name
Information]-[Sy
stem Contact]
SNMP-5
SNMP-6
[OKI Device [Network
Setup]-[SN Configuration]-[ SNMP]-[SysNa alphanumeric
MP]-[SysNa General
me] Settings]-[Syste
[Setup
Any
Set
SysName
me]
characters up to (printer
255 characters. model
(Default is null) name)
m Information]-
[System Name]
[OKI Device [Network
[Setup
Any
Set
Sys-Locatio
Setup]-[SN Configuration]-[ SNMP]-[SysLo alphanumeric
MP]-[SysLoc General
cation]
characters up to n (the
ation]
Settings]-[Syste
m Information]-
[System
255 characters. location
(Default is null) where the
printer is
Location]
installed)
SNMP-7
SNMP-8
[OKI Device
Setup]-[SN
MP]-[Defaul
t TTL]
[Setup
SNMP]-[Defaul
tTTL]
0—255
Set TTL
(Time To
Live) value
[OKI Device [Network
Setup]-[SN Configuration]-[ SNMP]-[Enabl
MP]-[Enable SNMP Traps]- eAuthenTrap]
[Setup
1 (Enable)/
2 (Disable)
Set
Authentic
Trap,
Authen
Trap]
enabled/
disabled
[MIB-II
Information]-[En
able
AuthenTraps]
C6100 Series Network User’s Guide
Configuration - 52
Ref. No.
Admin
Manager
Web browser
TELNET/
Diagnostic
test print
Available
options
Notes
NetWare-1 [OKI Device [Network
[Setup
ENABLE/
Set
Setup]-[Net Configuration]-[ NetWare]-[Net DISABLE
Ware]-[Use General
NetWare
protocol,
enabled/
disabled
Ware protocol]
NetWare
Protocol]
Settings]-[Protoc
ol
Options]-[NetWa
re]
NetWare-2 [OKI Device [Network
[Setup
ETHER-II/802.3/ Set primary
Setup]-[Net Configuration]-[ NetWare]-[Pac 802.2/SNAP/
NetWare
Ware]-[Fra General
me Type] Settings]-[Frame
ket type]
AUTO
packet type
Options]-[NetBE
UI]
NetWare-3 [OKI Device [Network
[Setup
RPRINTER/
Set
NetWare
mode
Setup]-[Net Configuration]-[ NetWare]-[Net PSERVER
Ware]-[Ope NetWare]-[NetW Ware mode]
ration
Mode]
are
Selections]-[Net
Ware Mode]
NetWare-4 [OKI Device [Network
[Setup
Any
Set file
Setup]-[Net Configuration]-[ NetWare]-[Set alphanumeric
servers to
Ware]-[Bind NetWare]-[File
ery Server for
Setup]-[Sel PServer
up PSERVER
mode]–
[FSERVER
name 1—8]
characters up to connect.
47 characters.
(Default is null)
Up to eight
file servers
can be set.
If you have
nine or
ected file
server]
Mode]-[File
Server Names]
more file
servers,
you should
set file
servers
here
NetWare-5 [OKI Device [Network
[Setup
Any
Set Print
Server
Setup]-[Net Configuration]-[ NetWare]-[Set alphanumeric
Ware]-[Print NetWare]-[PServ up PSERVER
characters up to name
Server
Name]
er
Mode]-[NetWare [Machine
Print Server
Name]
mode]–
31 characters.
(Default is [OL]
+ last six
digits of MAC
address)
name]
NetWare-6 [OKI Device [Network
[Setup
Any
Set
Setup]-[Net Configuration]-[ NetWare]-[Set alphanumeric
password
Ware]-[Bind NetWare]-[PServ up PSERVER
ery er mode]–
Setup]-[Pas Mode]-[Password [Password]
sword]
characters up to for Print
31 characters.
(Default is null)
Server
]
NetWare-7 [OKI Device [Network
[Setup
2—255 (4)
Set print
job polling
interval in
seconds
Setup]-[Net Configuration]-[ NetWare]-[Set
Ware]-[Bind NetWare]-[PServ up PSERVER
ery
er Mode]-[Job
mode]– [Job
polling
interval]
Setup]-[Job Polling Rate]
Polling
Time]
C6100 Series Network User’s Guide
Configuration - 53
Ref. No.
Admin
Manager
Web browser
TELNET/
Diagnostic
test print
Available
options
Notes
NetWare-8 [OKI Device [Network
[Setup
ENABLE/
Set bindery
mode,
enabled/
disabled.
Set
DISABLE if
you use
OkiLAN as
PSERVER
on NDS
Setup]-[Net Configuration]-[ NetWare]-[Set DISABLE
Ware]-[Bind NetWare]-[PServ up PSERVER
ery Setup]
er
mode]–
Mode]-[Bindery [Bindery
Mode]
mode]
[Setup
NetWare-9 [OKI Device [Network
Any
Set NDS
Setup]-[Net Configuration]-[ NetWare]-[Set alphanumeric
Ware]-[NDS NetWare]-[NDS] up PSERVER characters up to
mode] – [NDS 31 characters.
Tree name
Setup]-[ND -[Tree Name]
S Tree]
tree]
(Default is null)
NetWare-10 [OKI Device [Network
[Setup
Any
Set NDS
Setup]-[Net Configuration]-[ NetWare]-[Set alphanumeric
context for
Ware]-[NDS NetWare]-[NDS] up PSERVER
Setup]-[ND -[Context]
S Context]
characters up to Print Server
mode] – [NDS 77 characters.
context]
(Default is null)
NetWare-11 [OKI Device [Network
[Setup
Any
Set print
Setup]-[Net Configuration]-[ NetWare]-[SE alphanumeric
Ware]-[RPR NetWare]-[Remo T RPRINTER
INTER te Printer mode] –
Setup]-[Sel Mode]-[NetWare [PSERVEname (Default is null)
ected print Print Server
server] Names]
servers to
characters up to connect.
47 characters.
Up to eight
print
servers can
be set.
1—8]
If you have
nine or
more print
servers,
you should
set print
servers
here
NetWare-12 [OKI Device [Network
[Setup
4—255 (10)
Set
Setup]-[Net Configuration]-[ NetWare]-[SE
Ware]-[RPR NetWare]-[Remo T RPRINTER
duration
from the
last data’s
arrival to
freeing the
port in
INTER
te Printer Mode]- mode]–[Job
Setup]-[Tim
e Out]
timeout]
[Job Timeout]
seconds
EtherTalk-1 [OKI Device [Network
[Setup
ENABLE/
Set
Setup]-[Eth Configuration]-[ EtherTalk]-[Et DISABLE
EtherTalk,
enabled or
disabled
erTalk]-[Use General
herTalk
EtherTalk
Protocol]
Settings]-[Protoc protocol]
ol
Options]-[EtherT
alk]
EtherTalk-2 [OKI Device [Network
Setup]-[Eth Configuration]-[E EtherTalk]-[Zo alphanumeric
erTalk]-[Zon therTalk]-[EtherT ne name]
e Name] alk Zone Name]
[Setup
Any
Set Zone
Name to
characters up to which
32 characters.
([*])
OkiLAN
belongs.
C6100 Series Network User’s Guide
Configuration - 54
Ref. No.
Admin
Manager
Web browser
TELNET/
Diagnostic
test print
Available
options
Notes
NetBEUI-1 [OKI Device [Network
[Setup
ENABLE/
Set
Setup]-[Net Configuration]-[ NetBEUI]-[Net DISABLE
BEUI]-[Use General
NetBEUI,
enabled or
disabled.
BEUI protocol]
NetBEUI
Protocol]
Settings]-[Protoc
ol
Options]-[NetBE
UI]
NetBEUI-2 [OKI Device [Network
[Setup
Any
Set a
Setup]-[Net Configuration]-[ NetBEUI]-[Co alphanumeric
computer
BEUI]-[Com NetBEUI]-[NetBE mputer name] characters up to name for
puter
Name]
UI]-[Computer
Name]
15 characters.
(Default is [OL]
+ last six
OkiLAN.
digits of MAC
address)
NetBEUI-3 [OKI Device [Network
[Setup
Any
Set a work-
group name
Setup]-[Net Configuration]-[ NetBEUI]-[Wo alphanumeric
BEUI]-[Wor NetBEUI]-[NetBE rkgroup name] characters up to to which
kgroup]
UI]-[Workgroup
Name]
15 characters.
(Default is
[PrintServer])
OkiLAN
belongs.
NetBEUI-4 [OKI Device [Network
[Setup
Any
Set the
comments
Setup]-[Net Configuration]-[ NetBEUI]-[Co alphanumeric
BEUI]-[Com NetBEUI]-[NetBE mment]
ment] UI]-[Comment]
characters up to for OkiLAN.
48 characters.
(Default is
[EthernetBoar
d OkiLAN])
Port-1
Port-2
[OKI Device [Network
[Setup printer Any
Set
Setup]-[Net Configuration]-[ port]-[NetWar alphanumeric
NetWare
Ware]-[Print NetWare]-[NetW e port name] characters up to printer
er Name]
are
31 characters.
(Default is [OL] name
+ last six
digits of MAC
address +
-prn1])
object
Selections]-[Net
Ware Printer
Name]
[OKI Device [Network
Setup]-[Eth Configuration]-[E port]-[EtherTal alphanumeric
[Setup printer Any
Set
EtherTalk
erTalk]-[Prin therTalk]-[EtherT k port name] characters up to printer
ter Name]
alk Printer
Name]
32 characters.
(Default is the
printer name
on which
object
name
OkiLAN is
installed)
C6100 Series Network User’s Guide
Configuration - 55
Ref. No.
Admin
Manager
Web browser
TELNET/
Diagnostic
test print
Available
options
Notes
Port-3
[Setup printer Any
Set an
port]-[BOJ
string]
alphanumeric
and following
control
appropriate
command
sequenceto
characters up to be sent to
31 characters. the
(Default is null). connected
printer
\b Backspace
(0x08)
\t Tab (0x09)
\n Linefeed
(0x0a)
before
printing job
\v Vertical tab
(0x0b)
\f Page feed
(0x0c)
\r Carriage
return (0x0d)
\xnn Hex code
[nn] (0xnn)
\] Double quote
(0x22)
\\ Backslash
(0x5c)
Port-4
[Setup printer Any
Set an
port]-[EOJ
string]
alphanumeric
and following
control
appropriate
command
sequenceto
characters up to be sent to
31 characters. the
(Default is null) connected
printerafter
printing job
\b Backspace
(0x08)
\t Tab (0x09)
\n Linefeed
(0x0a)
\v Vertical tab
(0x0b)
\f Page feed
(0x0c)
\r Carriage
return (0x0d)
\xnn Hex code
[nn] (0xnn)
\] Double quote
(0x22)
\\ Backslash
(0x5c)
C6100 Series Network User’s Guide
Configuration - 56
Ref. No.
Admin
Manager
Web browser
TELNET/
Diagnostic
test print
Available
options
Notes
Port-5
[Setup printer Any
Set an
port]-[BOJ
alphanumeric
appropriate
command
sequenceto
string(KANJI)] and following
control
characters up to be sent to
31 characters. the
(Default is null) connected
printer
before
\b Backspace
(0x08)
printing job
when data
is sent to
sjis/euc
logical
printer/
directory
\t Tab (0x09)
\n Linefeed
(0x0a)
\v Vertical tab
(0x0b)
\f Page feed
(0x0c)
\r Carriage
return (0x0d)
\xnn Hex code
[nn] (0xnn)
\] Double quote
(0x22)
\\ Back slash
(0x5c)
Port-6
[Setup printer Any
port]-[EOJ alphanumeric
string(KANJI)] and following
control
Set an
appropriate
command
sequenceto
characters up to be sent to
31 characters. the
(Default is null) connected
printerafter
printing job
when data
is sent to
sjis/euc
logical
printer/
directory
\b Backspace
(0x08)
\t Tab (0x09)
\n Linefeed
(0x0a)
\v Vertical tab
(0x0b)
\f Page feed
(0x0c)
\r Carriage
return (0x0d)
\xnn Hex code
[nn] (0xnn)
\] Double quote
(0x22)
\\ Back slash
(0x5c)
C6100 Series Network User’s Guide
Configuration - 57
Ref. No.
Admin
Manager
Web browser
TELNET/
Diagnostic
test print
Available
options
Notes
Port-7
[Setup printer PS
port]-[Printer
type]
Set a
printer type
when data
is sent to
sjis/euc
logical
printer/
directory
Port-8
[Setup printer 0—16 (8)
port]-[TAB
size (char.)]
Set tab size
when data
is sent to
sjis/euc
logical
printer/
directory.
The value 0
does not
convert any
tabs
Port-9
[Setup printer 0—255 (78)
port]-[Page
width (char.)]
Set page
width when
data is sent
to sjis/euc
logical
printer/
directory. If
the width of
one line
exceeds
this value,
Carriage
Return and
Line Feed
are inserted
automatical
ly. The
value 0
means no
limitation of
the line
width
C6100 Series Network User’s Guide
Configuration - 58
Ref. No.
Admin
Manager
Web browser
TELNET/
Diagnostic
test print
Available
options
Notes
Port-10
[Setup printer 0—255 (66)
port]-[Page
length(line)]
Set page
length
when data
is sent to
sjis/euc
logical
printer/
directory.
If the
number of
lines
exceeds
this value,
Form Feed
are inserted
automatical
ly. The
value 0
means no
limitation of
the line
width
Port-11
[OKI Device
Setup]-[TCP
/IP]-[Use
FTP/LPD
[Setup printer NO/YES
port]-[lpr/ftp
banner]
Set banner
printing for
LPR/FTP
enabled/
disabled
Banner]
STATUS-1
STATUS-2
[Status]-[Pr [Printer Status] [Display
Display
logical port
status
inter
status]-[prn1]
Status]
[Setup]-[Sy [Network
[Display
Display
system
status
stem
Configuration]-[ status]-[syste
Status]
Network
Summary]
m]
Trap-1
[OKI Device [Network
[Setup printer Any
This
Setup]-[SN Configuration]-[ trap]-[Prn-Tra alphanumeric
community
MP]-[Printer SNMP Traps]-
p community] characters up to name is
Trap Setup .
. . ]-[Printer
Trap
Community
Name]
77 characters.
(Default is
[public])
assigned to
outgoing
printer
status traps
such as
off-line,
paper out,
etc.
[Trap
Destination]-[Pri
nter Trap
Community
Name]
C6100 Series Network User’s Guide
Configuration - 59
Ref. No.
Admin
Manager
Web browser
TELNET/
Diagnostic
test print
Available
options
Notes
Trap-2
[OKI Device [Network
Setup]-[SN Configuration]-[ trap]-
MP]-[Printer SNMP Traps]-
[Setup printer ENABLE/
DISABLE
[Setup
TCP#1—5
Set sending
a trap
packet
Trap Setup .
.
enabled or
disabled for
each
destination.
Five IP
address
[Trap
Assignments]-[Tr trap] –
.]-[TCP#1—
5]-[Detail . .
.]-[Trap
ap Enable]
[TCP#1—5
Trap enable]
Enable]
destinations
can be set
up and one
IPX
destination
Trap-3
Trap-4
Trap-5
[OKI Device [Network
[Setup printer ENABLE/
DISABLE
TCP#1—5
trap] –
[On-line trap]
Set sending
a trap,
enabled or
disabled,
when the
printer
Setup]-[SN Configuration]-[ trap]-[Setup
MP]-[Printer SNMP Traps]-
Trap Setup .
.
.]-[TCP#1—
5]-[Detail . .
.]-[On-line]
[Trap
Assignments]-[O
n-line]
turns to
ON-LINE
[OKI Device [Network
[Setup printer ENABLE/
DISABLE
TCP#1—5
trap] –
[Off-line trap]
Set sending
a trap,
enabled or
disabled,
when the
printer
Setup]-[SN Configuration]-[ trap]-[Setup
MP]-[Printer SNMP Traps]-
Trap Setup .
.
.]-[TCP#1—
5]-[Detail . .
.]-[Off-line]
[Trap
Assignments]-[O
ff-line]
turns to
OFF-LINE
[OKI Device [Network
Setup]-[SN Configuration]-[ trap]-[Setup
MP]-[Printer SNMP Traps]-
[Setup printer ENABLE/
Set sending
a trap,
enabled or
disabled,
when paper
is out
DISABLE
TCP#1—5
Trap Setup .
.
.]-[TCP#1—
5]-[Detail . .
.]-[Paper
Out]
trap] – [Paper
Out trap]
[Trap
Assignments]-[P
aper Out]
Trap-6
Trap-7
[OKI Device [Network
[Setup printer ENABLE/
Set sending
a trap
enabled or
disabled
when a
paper jam
occurs
Setup]-[SN Configuration]-[ trap]-[Setup
DISABLE
MP]-[Printer SNMP Traps]-
TCP#1—5
trap] – [Paper
Jam trap]
Trap Setup .
.
.]-[TCP#1—
5]-[Detail . .
.]-[Paper
Jam]
[Trap
Assignments]-[P
aper Jam]
[OKI Device [Network
Setup]-[SN Configuration]-[ trap]-[Setup
MP]-[Printer SNMP
Trap Setup . Traps]-[Trap
[Setup printer ENABLE/
Set sending
a trap
enabled or
disabled
when the
printer
cover opens
DISABLE
TCP#1—5
trap] – [Cover
.
Assignments]-[C Open trap]
.]-[TCP#1— over Open]
5]-[Detail . .
.]-[Cover
Open]
C6100 Series Network User’s Guide
Configuration - 60
Ref. No.
Admin
Manager
Web browser
TELNET/
Diagnostic
test print
Available
options
Notes
Trap-8
[OKI Device [Network
Setup]-[SN Configuration]-[ trap]-[Setup
MP]-[Printer SNMP
Trap Setup . Traps]-[Trap
[Setup printer ENABLE/
DISABLE
TCP#1—5
trap] –
Set sending
a trap
enabled or
disabled
when any
errors occur
.
Assignments]-[P [Printer Error
.]-[TCP#1— rinter Error]
5]-[Detail . .
trap]
.]-[Printer
Error]
Trap-9
[OKI Device [Network
Setup]-[SN Configuration]-[ trap]-[Setup
MP]-[Printer SNMP
Trap Setup . Traps]-[Trap
[Setup printer 0.0.0.0—
Set IP
255.255.255.25 address to
TCP#1—5
trap] –
5 (0.0.0.0)
which a
trap packet
will be sent.
You can set
up to five IP
addresses
.
Destination]-[Ad [TCP#1—5
.]-[TCP#1— dress 1]— Trap address]
5] [Address 5]
Trap-10
[OKI Device [Network
[Setup printer ENABLE/
DISABLE
Set sending
a trap
Setup]-[SN Configuration]-[ trap]-
MP]-[Printer SNMP Traps]-
packet
[Setup IPX
trap] –
[IPX Trap
enable]
Trap Setup .
. .]-[IPX]-
[Detail . .
.]-[Trap
enabled or
disabled for
each
[Trap
Assignments]-[Tr
ap Enable]
destination.
You can set
up to five IP
address
Enable]
destinations
and one IPX
destination.
Trap-11
Trap-12
Trap-13
[OKI Device [Network
Setup]-[SN Configuration]-[ trap]-
MP]-[Printer SNMP Traps]-
[Setup printer ENABLE/
DISABLE
[Setup IPX
trap] –
Set sending
a trap
enabled or
disabled
when the
printer
Trap Setup .
. .]-[IPX]-
[Detail . .
[Trap
Assignments]-[O [On-line trap]
n-line]
turns to
ON-LINE
.]-[On-line]
[OKI Device [Network
Setup]-[SN Configuration]-[ trap]-[
MP]-[Printer SNMP
Trap Setup . Traps]-[Trap
[Setup printer ENABLE/
DISABLE
Setup IPX
trap] –
Set sending
a trap
enabled or
disabled
when the
printer
. .]-[IPX]-
[Detail . .
.]-[Off-line]
Assignments]-
[Off-line]
[Off-line trap]
turns to
OFF-LINE.
[OKI Device [Network
Setup]-[SN Configuration]-[ trap]-
[Setup printer ENABLE/
DISABLE
Set sending
a trap
MP]-[Printer SNMP
enabled or
disabled
when paper
is out
[Setup IPX
trap] – [Paper
Out trap]
Trap Setup . Traps]-[Trap
. .]-[IPX]-
[Detail . .
.]-[Paper
Out]
Assignments]-[P
aper Out]
C6100 Series Network User’s Guide
Configuration - 61
Ref. No.
Admin
Manager
Web browser
TELNET/
Diagnostic
test print
Available
options
Notes
Trap-14
[OKI Device [Network
Setup]-[SN Configuration]-[ trap]-[Setup
MP]-[Printer SNMP Traps]-
[Setup printer ENABLE/
DISABLE
IPX trap] –
[Paper Jam
Set sending
a trap
enabled or
disabled
when a
paper jam
occurs
Trap Setup .
. .]-[IPX]-
[Detail . .
.]-[Paper
Jam]
[Trap
Assignments]-[P trap]
aper Jam]
Trap-15
Trap-16
[OKI Device [Network
[Setup printer ENABLE/
DISABLE
[Setup IPX
trap] – [Cover
Set sending
a trap
enabled or
disabled
when the
printer
cover opens
Setup]-[SN Configuration]-[ trap]-
MP]-[Printer SNMP Traps]-
Trap Setup .
. .]-[IPX]-
[Detail . .
.]-[Cover
Open]
[Trap
Assignments]-[C Open trap]
over Open]
[OKI Device [Network
Setup]-[SN Configuration]-[ trap]-
[Setup printer ENABLE/
DISABLE
Set sending
a trap
MP]-[Printer SNMP Traps]-
enabled or
disabled
when any
errors occur
[Setup IPX
trap] –
Trap Setup .
. .]-[IPX]-
[Detail . .
.]-[Printer
Error]
[Trap
Assignments]-[P [Printer Error
rinter Error] trap]
Trap-17
Trap-18
SMTP-1
[OKI Device [Network
Setup]-[SN Configuration]-[ trap]-
MP]-[Printer SNMP Traps]-
[Setup printer Any address
Set node
(00000000000 address to
)
which a
trap packet
will be sent
[Setup IPX
trap] – [IPX
Trap Setup .
. .]-[IPX]
[Trap
Destination]-[IP Trap address]
X]
[OKI Device [Network
[Setup printer Any address
Setnetwork
address to
which a
trap packet
will be sent
Setup]-[SN Configuration]-[ trap]-
(00000000)
MP]-[Printer SNMP Traps]-
[Setup IPX
trap] – [IPX
Trap Setup .
. .]-[IPX]
[Trap
Destination]-[IP Trap net]
X]
[OKI Device [Network
Setup]-[SM Configuration]-[E
[Setup SMTP
(E-Mail)]-
[SMTP
ENABLE/
DISABLE
Set sending
E-mail via
SMTP,
enabled or
disabled
TP]-
mail
Settings]-[Email
Transmit
[Use SMTP
Transmit
Protocol]
Transmit]
Settings]-
[SMTP Transmit]
SMTP-2
[OKI Device [Network
[Setup SMTP
(E-Mail)]-
[SMTP
ENABLE/
DISABLE
Set
Setup]-[SM Configuration]-[E
receiving
E-mail via
SMTP,
TP]-
mail
Settings]-[Email
Receive
[Use SMTP
Receive
Protocol]
Receive]
enabled or
disabled.
Settings]-
[SMTP Receive]
C6100 Series Network User’s Guide
Configuration - 62
Ref. No.
Admin
Manager
Web browser
TELNET/
Diagnostic
test print
Available
options
Notes
SMTP-3
[OKI Device [Network
Setup]-[SM Configuration]-[E
[Setup SMTP
(E-Mail)]-
[SMTP server
name]
0.0.0.0—
Set IP
255.255.255.25 address or
5 or host name host name
up to 64
characters.
(Default is null)
TP]-
mail
Settings]-[Email
Transmit
Settings]-
[SMTP Server]
of SMTP
server
[SMTP
Server
Address/
Name]
SMTP-4
SMTP-5
SMTP-6
SMTP-7
[OKI Device [Network
Setup]-[SM Configuration]-[E
TP]-[Advanc mail
[Setup SMTP
(E-Mail)]-
[SMTP port
number]
1—65535 (25)
Set port
number of
SMTP
ed . .
Settings]-[Email
Transmit
Settings]-
[SMTP Port
Number]
.]-[SMTP
Port
Number]
[OKI Device [Network
Setup]-[SM Configuration]-[E
TP]-[E-Mail mail
[Setup SMTP
(E-Mail)]-
[E-Mail
Any
alphanumeric
characters up to address
78 characters.
(Default is null) for [From]
field in the
Set the
E-mail
Address]
Settings]-[Email
Transmit
Settings]-
that is used
address]
mail header
[Printer Email
Address]
[OKI Device [Network
Setup]-[SM Configuration]-[E
TP]-[Reply- mail
To Address] Settings]-[Email
Transmit
[Setup SMTP
(E-Mail)]-[Repl
y-To address]
Any
alphanumeric
characters up to address
78 characters.
(Default is null) for
Set the
E-mail
that is used
Settings]-
[Reply-To-Addres
s]
[Reply-To]
field in the
mail header
[OKI Device [Network
Setup]-[SM Configuration]-[E
[Setup SMTP
Any
alphanumeric
characters up to to that
78 characters.
(Default is null) should be
sent. Up to
Set E-mail
addresses
(E-Mail)]-[Eve
nt to address
1—5] – [To
TP]-[1—
5]-[To
mail
Settings]-[Email
Address 1— Recipients]-[Ema
E-mail
Address 1—5]
5]
il Address 1]—
[Email Address
5]
five E-mail
addresses
can be set
SMTP-8
[OKI Device [Network
[Setup SMTP( DISABLE/
Set interval
that the
Setup]-[SM Configuration]-[E
30min/60min/
E-Mail)]-[Even
t to address
1—5] –
TP]-[1—
5]-[Check
Interval]
mail
Settings]-[Email
Alert
Assignments]-
[Re-send
Interval]
24hour
OkiLAN
checks
specified
event(s).
An E-mail is
sent when
specified
event(s)
[Re-send
Interval]
occur when
DISABLEis
selected
C6100 Series Network User’s Guide
Configuration - 63
Ref. No.
Admin
Manager
Web browser
TELNET/
Diagnostic
test print
Available
options
Notes
SMTP-9
[OKI Device [Network
[Setup SMTP
(E-Mail)]-[Eve
nt to address
1—5] – [Off
Line]
ENABLE/
DISABLE
An E-mail is
sent when
the printer
is Off- line if
this is
Setup]-[SM Configuration]-[E
TP]-[1—
mail
5]-[Selected Settings]-[Email
condition]
Alert
Assignments]-
[Off Line]
enabled
SMTP-10
SMTP-11
SMTP-12
[OKI Device [Network
Setup]-[SM Configuration]-[E
TP]-[1—5]- mail
[Setup SMTP
(E-Mail)]-[Eve
nt to address
1—5] –
[Consumable
Message]
ENABLE/
DISABLE
An E-mail is
sent when
maintenanc
e is
required if
this is
enabled
[Selected
condition]
Settings]-[Email
Alert
Assignments]-[C
onsumable
Message]
[OKI Device [Network
Setup]-[SM Configuration]-[E
TP]-[1—5]- mail
[Setup SMTP
(E-Mail)]-[Eve
nt to address
1—5] – [Toner
Low/Out]
ENABLE/
DISABLE
An E-mail is
sent when
toner(s)
low/out
occurs if
this is
enabled
[Selected
condition]
Settings]-[Email
Alert
Assignments]-[T
oner Low Toner
Out]
[OKI Device [Network
Setup]-[SM Configuration]-[E
TP]-[1—5]- mail
[Setup SMTP
(E-Mail)]-[Eve
nt to address
1—5] – [Paper
Low/Out]
ENABLE/
DISABLE
An E-mail is
sent when
paper low/
out occurs if
this is
[Selected
condition]
Settings]-[Email
Alert
Assignments]-[P
aper Low Paper
Out]
enabled
SMTP-13
SMTP-14
SMTP-15
[OKI Device [Network
Setup]-[SM Configuration]-[E
TP]-[1—5]- mail
[Setup SMTP
ENABLE/
DISABLE
An E-mail is
sent when a
paper jam
occurs if
(E-Mail)]-[Eve
nt to address
1—5] – [Paper
Jam]
[Selected
condition]
Settings]-[Email
Alert
Assignments]-[P
aper Jam]
this is
enabled
[OKI Device [Network
Setup]-[SM Configuration]-[E
TP]-[1—5]- mail
[Setup SMTP
(E-Mail)]-[Eve
nt to address
1—5] – [Cover
Open]
ENABLE/
DISABLE
An E-mail is
sent when
the cover is
opened if
this is
[Selected
condition]
Settings]-[Email
Alert
Assignments]-[C
over Open]
enabled
[OKI Device [Network
Setup]-[SM Configuration]-[E
TP]-[1—5]- mail
[Setup SMTP
(E-Mail)]-[Eve
nt to address
1—5] –
[Stacker
Error]
ENABLE/
DISABLE
An E-mail is
sent when
any stacker
error occurs
if this is
[Selected
condition]
Settings]-[Email
Alert
Assignments]-[S
tacker Error]
enabled
C6100 Series Network User’s Guide
Configuration - 64
Ref. No.
Admin
Manager
Web browser
TELNET/
Diagnostic
test print
Available
options
Notes
SMTP-16
[OKI Device [Network
Setup]-[SM Configuration]-[E
TP]-[1—5]- mail
[Setup SMTP
(E-Mail)]-[Eve
nt to address
1—5] – [Mass
Storage Error]
ENABLE/
DISABLE
An E-mail is
sent when
any mass
storage
error occurs
if this is
enabled
[Selected
condition]
Settings]-[Email
Alert
Assignments]-[M
ass Storage
Error]
SMTP-17
SMTP-18
[OKI Device [Network
[Setup
ENABLE/
An E-mail is
sent when
any
Setup]-[SM Configuration]-[E SMTP(E-Mail)] DISABLE
TP]-[1—5]- mail
-[Event to
Settings]-[Email address 1—5]
Alert –[Recoverable
[Selected
condition]
recoverable
error occurs
if this is
Assignments]-[R Error]
ecoverable Error]
enabled
[OKI Device [Network
Setup]-[SM Configuration]-[E
TP]-[1—5]- mail
[Setup SMTP
(E-Mail)]-[Eve
nt to address
1—5] –
[Service Call
Req.]
ENABLE/
DISABLE
An E-mail is
sent when
any service
call request
occurs if
this is
enabled
[Selected
condition]
Settings]-[Email
Alert
Assignments]-[S
ervice Call
Required]
SMTP-19
SMTP-20
[OKI Device [Network
Setup]-[SM Configuration]-[E
TP]-[1—5]- mail
[Setup SMTP
(E-Mail)]-[Eve
nt to address
1—5] –
ENABLE/
An E-mail is
sent when
any finisher
error occurs
if this is
DISABLE
[Selected
condition]
Settings]-[Email
Alert
Assignments]-[Fi
nisher Error]
[Finisher]
enabled
[OKI Device [Network
Setup]-[SM Configuration]-[E
TP]-[Advanc mail
[Setup SMTP
(E-Mail)]-[Sig
nature line 1—
4]
Any
alphanumeric
characters up to signature
63 characters.
(Default is null) Signature is
added to
Set up to
four
ed . .
Settings]-[Email
lines.
.]-[Signatur Signature]-[Sign
e]
ature line 1]—
[Signature line
4]
the bottom
of an E-mail
ETC-1
ETC-2
[Setup]-[Re [Network
Reset to
Reset
set]
Configuration]-[ factory set
General
OkiLAN
settings to
factory
default
Settings]-[Restor
e Factory
Defaults]
[Network
Configuration]-[
General
Settings]-[Syste
m Information]-
[Printer Serial
Number]
Read only
item.
Printer
serial
number is
displayed
C6100 Series Network User’s Guide
Configuration - 65
Ref. No.
Admin
Manager
Web browser
TELNET/
Diagnostic
test print
Available
options
Notes
ETC-3
[Network
Configuration]-[
General
Settings]-[Syste
m Information]-
[Printer Asset
Number]
Any
alphanumeric
characters up to asset
8 characters.
Set a
printer
number
(Default is null)
Configurable items vary between printers.
C6100 Series Network User’s Guide
Configuration - 66
Management Utility
PrintSuperVision
PrintSuperVision is a web-based application for managing printing
devices connected to a network. It consists of two parts:
A web application based on Microsoft web server (Internet
Information Server, IIS or Personal WEB Server, PWS), that
provides the user interface.
A monitoring program (PrintSuperVisor) that runs all the time,
collecting data and saving it in a database for statistical reports and
sending E-mail alerts based on the saved configuration.
PrintSuperVision’s main functions are:
>
Maintaining the list of printing devices and organising them in
logical groups.
>
Initially discovering and configuring printers connected to the
network.
>
>
Locating printers visually on maps.
Monitoring devices over time and saving data for statistical
reports.
>
Sending email alerts when events occur that affect the
functionality of printers.
>
>
>
Creating statistical reports about usage of printers.
Tracking maintenance data related to printers.
Integrating with Oki Data’s on-line web support.
C6100 Series Network User’s Guide
Configuration - 67
System requirement
Windows
The main PrintSuperVision application can be installed in any of the
following Windows systems.
Operating System Service Option IIS/PWS
Pack
Pack
Windows NT 4.0
Workstation
6.0
4.0
PWS (Personal Web Server)
available in NT 4.0 Option Pack
Windows NT 4.0
Server
5.0
—
4.0
—
IIS (Internet Information
Server) 1.0
Windows XP Home/
Professional
IIS installed as an option.
Available in the Windows XP CD
Windows 2000
Professional
1.0
1.0
—
Internet Service Manager
included in the OS
Windows 2000
Server/Advanced
Server
—
Internet Service Manager
included in the OS
Windows 98
—
—
—
—
PWD (Included in Windows 98
by default)
PWS available in NT 4.0 Option
Pack in Microsoft Web site
Windows 98 SE
PWD (Included in Windows 98
by default. PWS available in NT
4.0 Option Pack in Microsoft
Web site
While the PrintSuperVision application may work in Windows 95
with PWS installed, PrintSuperVision may not install or work
properly in some versions of Windows 95. However, as a client,
Windows 95 is fully supported.
Microsoft does not officially support Windows Me-PWS in Windows
Me. PrintSuperVision does not support this OS. Also, Microsoft no
longer supports Peer Web Service. PrintSuperVision will not work
with Peer Web Service.
C6100 Series Network User’s Guide
Configuration - 68
Supported Browsers
The browsers supported are:
Internet Explorer (IE) 4.01 and above.
Netscape Navigator 4.0 and above.
Opera 5.12 and above.
The PrintSuperVision application can be accessed from any
Windows, Macintosh, Unix, or Linux desktop that supports any of
the above-mentioned browsers.
While all the above browsers are supported, PrintSuperVision
works best when used with Internet Explorer. When using the
Netscape browser, do not select the option [Images off]. The
hyperlinks may not work properly. Some versions of Netscape
browser do not display the frames properly, and the [Back] button
may not work correctly.
Supported Printers
PrintSuperVision provides general management information for
OKI and non-OKI printers connected to the network. For OKI
printers using OkiLAN print servers, additional details, reports and
added features are available.
While the printer properties are displayed in PrintSuperVision, only
a few of the printer settings can be set. For setting any other
printer settings, a hyperlink to the printer’s web page is provided
in PrintSuperVision.
C6100 Series Network User’s Guide
Configuration - 69
Installation
To install the Print SuperVision utility
Note: You must be connected to the internet to download this
utility.
WindowsXP/2000/NT4.0 requires administrator privileges.
1. Insert the CD-ROM provided with your printer into the
CD-ROM drive.
If the Menu Installer doesn’t start automatically, click
Start→Run→Browse. Browse to your CD-ROM. Click
Setup→Open→OK.
2. Select [Internet Downloads].
3. Select [PrintSuperVision].
4. Follow the on-screen instructions. In the [Edit Data] screen,
you can specify a port number for PrintSuperVision (default
80).
5. When installation ends, the [Setup complete] screen is
displayed. Click [Finish].
6. Now you should select
[Start]-[Programs]-[PrintSuperVision]-[PrintSuperVision] or
double-click the [PrintSuperVision] icon on the desktop for
the PrintSuperVision server.
7. For PrintSuperVision client, access [http://[the server IP
address or host name]/PrintSuperVision] from the Web
browser. If you change the port number you should add
[:[port number]] such as [http://172.168.20.127/
PrintSuperVision:8080].
8. PrintSuperVision has an on-line help facility.
C6100 Series Network User’s Guide
Configuration - 70
Uninstallation
To uninstall PrintSuperVision, either
>
select [Start] → [Programs]→[PrintSuperVision]→[Uninstall
PrintSuperVision],
or
>
from [Control Panel], select [Add/Remove Programs], select
[PrintSuperVision] from the index window and click [Add/
Remove]. When the uninstallation is completed, close [Add/
Remove Programs].
In some cases, an empty [Okidat/PrintSuperVision/] directory may
be left behind. Delete the directory manually.
C6100 Series Network User’s Guide
Configuration - 71
Printing Utility
OKI LPR
The OKI LPR Utility is a utility that allows printing data to printers
connected to the network via TCP/IP. This utility is for use with
Windows XP, Windows 2000, Windows Me, Windows 98, Windows
95 and Window NT4.0.
The utility is for those OKI printers which support TCP/IP; it
redirects printing data to the lpr port of the specified IP address.
System Requirement
Windows XP/2000/Me/98/95/NT4.0 with TCP/IP support.
To install the OKI LPR utility
The OKI LPR utility requires that the TCP/IP protocol should be
installed in your Windows system. To install the TCP/IP protocol
into your Windows system consult your Windows manual.
Windows XP/2000/NT4.0 requires administrator privileges.
1. Set up the printer driver by designating the output
destination to [Local Printer (LPT1:)]. For information on
setting up your printer driver, see the printer user manual.
2. Insert the CD-ROM provided with your printer into the
CD-ROM drive.
If the Menu Installer doesn’t start automatically, click
Start→Run→Browse. Browse to your CD-ROM. Click
Setup→Open→OK.
3. Select [Optional Utilities].
4. Select [Install Direct Network Printing Utility (LPR)]
5. Click [Next] when the [Welcome] screen is displayed.
C6100 Series Network User’s Guide
Configuration - 72
6. Verify [Destination Folder] and [Spool Folder] and click
[Next].
7. Check [Register in Startup] if you want automatic startup as
Windows boots up. Check [Launch as minimized] if you want
to startup in the Icon state and click [Next].
8. Verify the program folder name and click [Next]. The
installation starts.
9. When the installation ends, the [Setup complete] screen is
displayed. Check [Yes, I want to launch OKI LPR Utility now]
and click [Finish]. Check [Yes, I want to view the ReadMe
File] if you want to read [Readme]. The OKI LPR utility
starts.
10. Select [Add Printer] on the [Remote Print] menu.
11. Select [Printer] to accept the printer that has been added in
the step 1.
12. Enter an IP address at [IP Address] and click [OK]. A printer
is added to the main window.
Refer to the On-line Help for information on how to use the utility.
C6100 Series Network User’s Guide
Configuration - 73
Uninstallation
1. Stop the OKI LPR Utility. Right-click the OKI LPR icon in the
system tray and click [Exit].
2. Select [Start] → [Program] → [Okidata] → [OKI LPR Utility]
→ [Uninstall OKI LPR Utility] ([Start] → [All Programs] →
[Okidata] → [OKI LPR Utility] → [Uninstall OKI LPR Utility]
on WindowsXP).
3. Click [Yes] when the [Confirm File Deletion] dialogue is
displayed. Deletion of the OKI LPR utility starts.
4. When the deletion has finished, the [Uninstall Complete]
screen is displayed. Click [OK].
If a file that has been added after installation exists in the folder to
install the OKI LPR utility or the folder to spool, you cannot delete
the folder. Delete any unwanted files before running [Uninstall OKI
LPR Utility].
C6100 Series Network User’s Guide
Configuration - 74
Microsoft Windows
Overview
This chapter provides guidelines on how to print over the network
from various Microsoft Windows platforms. There are numerous
ways of printing from Windows and the exact set-up will vary
depending upon your environment. There are also numerous
versions of Windows, which can be configured as either a client,
server or both.
Although there are many variants of Windows, the principles of
network printing are the same. Microsoft provides on-line help with
all of their operating systems and this is a good reference point for
the exact details of each configuration option within Windows.
The network printer supports the following protocols that can be
used in conjunction with the Windows operating system:
>
>
>
TCP/IP
IPX (Novell NetWare)
NetBEUI
OkiLAN 8300e Network User’s Guide
Microsoft Windows - 75
Installation of TCP/IP Protocol
There are a number of options available when printing using TCP/
IP for Windows. The following table lists the options:
Windows Version
Method
Win 95/98/Me
NT 4.0
OKI LPR Utility
OKI LPR Utility
Microsoft LPR1
OKI LPR Utility
Windows 2000/ Windows XP
Microsoft LPR1
Port 91001
IPP1
1
These functions are built into Windows and are displayed as options when using the Add Printer
Wizard.
Although there are some differences in configuration options
between the various Windows platforms, the procedure for printing
using TCP/IP is the same.
1. Ensure that the TCP/IP protocol has been installed in
Windows. This can be confirmed by checking the network
settings from within the Control Panel. If TCP/IP has not
been installed refer to the section below Installation of TCP/
IP protocol.
2. If not already configured, a suitable IP address, Subnet
Mask and Gateway address should be configured. Please
refer to the on-line help if necessary. It is vital that the IP
address entered is unique and valid. Entering an incorrect IP
address may cause severe network problems. Please check
the address with the network administrator.
3. If your network environment uses domain names, DNS
should be enabled and configured on your system. However,
this step is not essential to enable network printing.
4. Restart the operating system.
OkiLAN 8300e Network User’s Guide
Microsoft Windows - 76
Windows 95/98/Me
1. Click the [Start] button, select [Settings] and then click
[Control Panel].
2. In the [Control Panel] double-click on the [Network] icon.
3. In the [Network] dialogue box click [Configuration Panel].
4. If the [Client for Microsoft Networks] is not listed, click
[Add].
5. In the [Select Network Component Type] dialogue box,
select [Protocol] then click [Add].
6. In the [Select Network Protocol] dialogue box, select
[Microsoft] from the list of manufacturers, then select [TCP/
IP] from the list of network protocols, then click [OK].
7. The Windows installation CD-ROM may be required. Follow
the remaining dialogue box prompts.
Windows NT 4.0
1. Click [Start], select [Settings] and then click [Control
Panel].
2. Double-click the [Network] icon.
3. In the Network dialogue box, click the [Protocols] tab.
4. If the [TCP/IP Protocol] is not listed, click [Add].
5. In the [Select Network Protocol] dialogue box, select [TCP/
IP Protocol] and click [OK].
6. The Windows NT installation CD-ROM may be required.
Follow the remaining dialogue box prompts.
OkiLAN 8300e Network User’s Guide
Microsoft Windows - 77
Windows 2000
1. Click the [Start] button, select [Settings] and then click
[Network and Dial-up Connections].
2. Double-click the [Local Area Connection] icon. In the [Local
Area Connection Status] dialogue box, click [Properties].
3. In the [Local Area Connection Properties] dialogue box, click
[Install].
4. In the [Select Network Component Type] dialogue box,
select [Protocol] and click [Add].
5. In the [Select Network Protocol] dialogue box, select [TCP/
IP Protocol] and click [OK].
6. Click [Close] button in the [Local Area Connection
Properties] dialogue box.
7. Click [Close] in the [Local Area Connection Status] dialogue
box.
Windows XP
1. Click the [Start] button and select [Control Panel].
2. Select [Network and Internet Connection] and [Network
Connection].
3. Double-click [Local Area Connection] and click [Properties]
in the [Location Area Connection Status] dialogue box.
4. If the [Internet Protocol (TCP/IP)] is not listed, click
[Install.].
5. In the [Select Network Component Type] dialogue box,
select [Protocol] then click [Add].
6. In the [Select Network Protocol] dialogue box, select
[Internet Protocol (TCP/IP)] then click [OK].
OkiLAN 8300e Network User’s Guide
Microsoft Windows - 78
7. The Windows XP installation CD-ROM may be required.
Follow the remaining dialogue box prompts.
Once the protocol has been installed and configured in Windows,
the next step is to configure the TCP/IP parameters in the network
printer.
OkiLAN 8300e Network User’s Guide
Microsoft Windows - 79
Network printer IP address configuration
Use the Admin/Manager Standard Set-up Utility to configure the IP
Address, Subnet Mask and Gateway.
1. Connect the printer to the network and turn on.
2. Place the Network Software Utilities disk (or the software CD
provided with your printer) in the CD-ROM drive. The set-up
utility starts automatically. If the set-up utility does not
start, double-click on setup.exe in the Windows folder of the
CD-ROM.
3. Select [Install Network Setup Utility].
4. Select the appropriate language.
5. Click [Next] on the Welcome screen.
6. If you agree to the User License Agreement, click [Next].
7. Select the appropriate print server, using the Ethernet
address to identify it, and click [Next].
The Ethernet address (MAC Address) of the printer can be
found on the self-diagnostic printout, which can be printed by
pressing the push-button on the network card for two
seconds and then releasing it.
Do you use the TCP/IP protocol?
When using lpr in UNIX and other TCP/IP environments,
please select [Yes]. To use in a TCP/IP environment, an IP
address should be assigned to the Ethernet board.
If [Yes] has been selected and TCP/IP is the only working
protocol and the IP address has not already been assigned,
you can either obtain an IP address automatically or assign
an IP address.
OkiLAN 8300e Network User’s Guide
Microsoft Windows - 80
When [Obtain an IP address automatically] is selected, the
device IP address will be automatically assigned by the DHCP
server. In an environment without a DHCP server, please
assign the IP address manually.
If you are assigning an IP address, you need to enter:
>
>
>
An IP address
Subnet mask
Gateway address.
8. Click [Next].
Do you use the NetWare protocol?
Consult your network manager to ensure that the NetWare
file server is properly installed and working on the network.
Make sure that NetWare Client32 or IntranetWare Client is
installed on your computer.
9. On selecting [Yes] you will be asked if [You set-up the queue
from the Wizard]?
Do you use the EtherTalk protocol?
EtherTalk is the required protocol for printing data from the
Macintosh environment.
Do you use the NetBEUI protocol?
Using NetBEUI makes it easy to manage your OKI product
and print within the network environment of Windows.
10. Confirm your configuration. If everything is correct, select
[Execute] to apply the configuration. Set-up has now been
completed. Select [Finish].
OkiLAN 8300e Network User’s Guide
Microsoft Windows - 81
Now that both Windows and the printer have been configured to
use TCP/IP, the next step is to configure Windows to print to the
network printer.
Windows 95/98/Me
When printing using TCP/IP, the Oki LPR utility is the only option to
use. The following procedure should be used.
When installing the driver, ensure it is installed as a local printer
and not a network printer. Ensure the appropriate printer driver
has been installed in Windows.
and add the printer installed earlier.
Windows NT 4.0
With Windows NT 4.0, you have two options for printing using TCP/
IP. They are:
>
>
Oki LPR
Microsoft LPR
In order to use Microsoft LPR, it must first be installed into your
operating system.
NT 4.0 requires administrator privileges.
Oki LPR
Please follow the procedure described in the Windows 95/98/Me
section on page 82.
Microsoft LPR
To install this port, the following needs to be carried out.
1. Select [Start], [Settings], [Control Panel] and then select
[Printers].
OkiLAN 8300e Network User’s Guide
Microsoft Windows - 82
2. Select [Add Printer] Wizard.
3. Select [My Computer] and then [Next].
4. Select [Add Port].
5. Select [LPR Port] and then [OK].
6. In [Name or address of server providing lpd] type the host
name or IP address of the host for the printer you are
adding.
7. In [Name of printer or print queue on that server] type the
logical printer name "lp" and then click [OK].
8. Follow the instructions on the screen to finish installing the
LPR-compatible printer.
If the LPR port is not available, install the Microsoft TCP/IP Printing
Service.
Insert the printer driver for Windows NT4.0.
1. Select [Start]→[Settings]→[Control Panel] and then double-
click the [Network] icon.
2. In the Network dialogue box, click the [Services] tab.
3. If [Microsoft TCP/IP Printing] is not listed, click [Add].
4. In the [Select Network Service] dialogue box, select
[Microsoft TCP/IP Printing] and click [OK].
5. The Windows NT installation CD-ROM may be required.
Follow the remaining dialogue box prompts.
OkiLAN 8300e Network User’s Guide
Microsoft Windows - 83
Windows 2000
Windows 2000 requires administrator privileges.
With Windows 2000, there are four options for printing using TCP/
IP.
>
>
>
>
Oki LPR
Microsoft LPR
Port 9100
IPP
In order to use Microsoft LPR, it must first be installed on your
system.
OKI LPR
Please follow the procedure described in the Windows 95/98/Me
section on page 82.
Microsoft LPR
To install this port, the following needs to be carried out:
1. Select [Start], [Settings], [Control Panel and Printers].
2. Open the [Printers] folder.
3. Double-click [Add Printer] and then select [Next].
4. Select [Local Printer], clear the [Automatically detect my
printer] check box, and then select [Next].
5. Select [Create a new port] and then [LPR Port].
6. Select [Next] and then provide the following information:
OkiLAN 8300e Network User’s Guide
Microsoft Windows - 84
In [Name or address of server providing LPD] enter the host
name or Internet Protocol (IP) address of the host for the
printer you are adding.
In [Name of printer or print queue on that server] type lp.
Follow the instructions on the screen to finish installing the
TCP/IP printer.
Port 9100
1. Select [Start] → [Settings] → [Control Panel].
2. Open the [Printers] folder.
3. Double-click [Add Printer] and then select [Next].
4. Select [Local Printer], clear the [Automatically detect my
printer] check box and then click [Next].
5. Select [Create a New Port] and select [ Standard TCP/IP
Port].
6. Select [Next].
7. The [Welcome to the Add Standard TCP/IP Printer Port
Wizard] will appear.
8. Select [Next] and provide the following information. Enter
[Printer name] or IP address, for example: 172.168.1.31. If
the above IP address is entered, the Port Name will default
to IP_172.168.1.31.
9. Select [Next]. Additional port information will be required.
10. Under [Device Type], select [Custom] then [Settings].
11. Ensure [Protocol] is set to [Raw].
12. Ensure [Port Number] is 9100 and [SNMP Status Enabled] is
deselected.
OkiLAN 8300e Network User’s Guide
Microsoft Windows - 85
13. Select [OK].
14. Select [Follow the instructions on the screen to finish
installing the printer.]
IPP
1. Select [Start]→[Settings]→[Control Panel and Printers].
2. Open the [Printers Folder].
3. Double-click [Add Printer] and then select [Next].
4. Select [Network Printer].
5. Select [Next].
6. Type printer URL in text box labelled [Connect to a printer in
the Internet or your Intranet], e.g. http://172.168.1.31/ipp/
lp.
7. Select [Next].
8. Install printer driver.
OkiLAN 8300e Network User’s Guide
Microsoft Windows - 86
Windows XP
Windows XP requires administrator privileges.
With Windows XP, there are four options for printing using TCP/IP.
>
>
>
>
Oki LPR
Microsoft LPR
Port 9100
IPP
In order to use Microsoft LPR, it must first be installed on your
system.
OKI LPR
Please follow the procedure described in the Windows 95/98/Me
section on page 82.
Microsoft LPR
To install this port, the following needs to be carried out:
1. Select [Start]→[Settings]→[Control Panel]→[Printers and
Other Hardware].
2. Select [Printers and Faxes].
3. Click [Add Printer], then select [Next].
4. Select [Local printer attached to this computer], clear the
[Automatically detect and install my Plug and Play printer]
check box, and then click [Next].
5. Select [Create a New Port] and [Type Standard TCP/IP
Port].
OkiLAN 8300e Network User’s Guide
Microsoft Windows - 87
6. Click [Next].
7. [Welcome to the Add Standard TCP/IP Printer Port Wizard]
appears.
8. Click [Next] and provide the following information. Enter
[Printer name or IP address], for example: 172.168.1.31. If
the above IP address is entered, the Port Name will default
to IP_172.168.1.31.
9. Click [Next]. [Additional Port Information Required]
displayed.
10. Under [Device Type], select [Custom] then [Settings].
11. Ensure [Protocol] is set to [LPR].
12. Ensure [Queue Name] is lp and [SNMP Status Enabled] is
deselected.
13. Click [OK].
14. Follow on screen instructions to finish installing the printer.
Port 9100
1. Select [Start]→[Settings]→[Control Panel]→[Printers and
Other Hardware].
2. Select [Printers and Faxes].
3. Click [Add Printer] and then click [Next].
4. Select [Local printer attached to this computer], clear the
[Automatically detect and install my Plug and Play printer]
check box, and then click[Next].
5. Select [Create a New Port] and select [Type Standard TCP/IP
Port].
6. Click [Next].
OkiLAN 8300e Network User’s Guide
Microsoft Windows - 88
7. [Welcome to the Add Standard TCP/IP Printer Port Wizard]
appears.
8. Click [Next] and provide the following information. Enter
[Printer name or IP address], for example: 172.168.1.31. If
the above IP address is entered, the Port Name will default
to IP_172.168.1.31.
9. Click [Next]. [Additional Port Information Required] is
displayed.
10. Under [Device Type], select [Custom] then [Settings].
11. Ensure [Protocol] is set to [Raw].
12. Ensure [Port Number] is 9100 and [SNMP Status Enabled] is
deselected.
13. Click [OK].
14. Follow the instructions on the screen to finish installing the
printer.
IPP
1. Select [Start], [Settings], [Control Panel]. and [Printers and
Other Hardware].
2. Select [Printers and Faxes].
3. Click [Add Printer] and then select [Next].
4. Select [A network printer, or a printer attached to another
computer].
5. Click [Next].
6. Select [Connect to a printer on the Internet or on a home or
office network] and type printer URL in text box, e.g. http://
172.168.1.31/ipp/lp.
OkiLAN 8300e Network User’s Guide
Microsoft Windows - 89
7. Click [Next].
8. Install printer driver
OkiLAN 8300e Network User’s Guide
Microsoft Windows - 90
Novell Netware IPX
IPX is used with Novell NetWare. The OkiLAN supports Novell 3, 4,
5 and 6, and allows print jobs to be directed to the appropriate
Novell print queue. Please refer to the relevant section of this
manual for additional information.
NetBEUI Protocol
NetBEUI is a protocol that was designed for use on small
workgroups or LANs. Within Windows, NetBEUI is used for file and
printer sharing between computers. It provides a simple method of
printing, but the protocol does have limitations and is not as robust
as TCP/IP or IPX. Typically it is employed in small or home
networks.
Network Printer Settings
There are three configurable items under NetBEUI within the
printer. These can be configured using the standard set-up utility
described in Chapter 1.
Computer Name:
Workgroup:
Name assigned to the printer
PrintServer1
Comment:
User definable description
1
Although the workgroup name can be changed, it is recommended that it remain PrintServer.
Although there are some differences in configuration options
between the various Windows platforms, the procedure for printing
using NetBEUI is the same.
Please ensure the NetBEUI protocol has been installed in Windows.
This can be confirmed by checking the network settings. If NetBEUI
has not been installed please refer to the section below.
The relevant Windows installation CD-ROM may be required and
you should follow the on-screen dialogue box prompts.
OkiLAN 8300e Network User’s Guide
Microsoft Windows - 91
Windows 95/98/Me
1. Click [Start] → [Settings] → [Control Panel].
2. In the Control Panel double-click on the [Network] icon.
3. In the Network dialogue box select [Configuration Panel].
4. If [Client for Microsoft Networks] is not listed, click [Add].
5. In the [Select Network Component Type] dialogue box,
select [Protocol] then [Add].
6. In the [Select Network Protocol] dialogue box, select
[Microsoft] from the list of manufacturers, then select
[NetBEUI] from the list of [Network Protocols] and then click
[OK].
7. The Windows installation CD-ROM may be required. Follow
the remaining dialogue box prompts.
Windows NT 4.0
1. Click the [Start] button, select [Settings] and then [Control
Panel].
2. Double-click the [Network] icon.
3. In the [Network] dialogue box, click the [Protocols] tab.
4. If the [NetBEUI Protocol] is not listed, click [Add].
5. In the [Select Network Protocol] dialogue box, select
[NetBEUI Protocol] and click [OK].
OkiLAN 8300e Network User’s Guide
Microsoft Windows - 92
Windows 2000
1. Click the [Start] button, select [Settings] and then click
[Network and Dial-up Connections].
2. Double-click the [Local Area Connection] icon. In the [Local
Area Connection Status] dialogue box, click [Properties].
3. In the [Local Area Connection Properties] dialogue box, if
the [NetBEUI Protocol] is not listed, click [Install].
4. In the [Select Network Component Type] dialogue box,
select [Protocol] and click [Add].
5. In the [Select Network Protocol] dialogue box, select
[NetBEUI Protocol] and click [OK].
6. Click [Close] in the [Local Area Connection Properties]
dialogue box.
7. Click the [Close] button in the [Local Area Connection Status]
dialogue box.
OkiLAN 8300e Network User’s Guide
Microsoft Windows - 93
Windows XP
Although you can install the NetBEUI protocol into Windows XP, it
is not supported. You should be able to use NetBEUI on LAN
connections although you will not be able to use this on Remote
Access Service Connections.
1. In the [Start] menu, select [Settings] then [Control Panel].
2. Double-click [Network Connections].
3. Right-click the adapter you wish to add NetBEUI to and then
click [Properties].
4. On the [General] tab, select [Install].
5. Select [Protocol] and then [Add].
6. Select [Have Disk] and insert your Windows XP CD-ROM.
Open the Valueadd\msft\net\netbeui folder, click the
Netnbf.inf file and then click [Open]. Now the printer has
been configured and NetBEUI has been installed; you can
configure Windows to print over the network.
OkiLAN 8300e Network User’s Guide
Microsoft Windows - 94
Printer driver configuration
In the following example, the printer has been configured as
follows:
Computer Name:
OL07DB85
Workgroup:
Comment:
PrintServer
EthernetBoard OKILAN
1. Set up the printer driver as the default local printer.
2. In the [Start] menu, select [Settings] then [Printers].
3. Select the relevant printer driver, then [Properties].
4. Click on the [Details] tab in the printer driver.
5. Select [Add Port]. Select [Network] and click [Browse].
6. Double-click [Entire Network], [PrintServer] and
[OL07DB85].
7. Select [Prn1] and click OK.
8. Check that [Network] is selected and click [OK].
9. Select [Apply] and [OK] to close [Properties].
>
Printing can be carried out using the application software.
>
The Master Browser function manages machine information
from the same Workgroup, and replies to summary requests
from other workgroups.
>
The Master Browser function operates only if the Workgroup
name is PrintServer.
OkiLAN 8300e Network User’s Guide
Microsoft Windows - 95
>
The Master Browser function can only manage this network
card. If the PrintServer name is put into another Workgroup,
the network card will not be able to find it on the network.
>
>
A maximum of eight Ethernets can be managed by the Master
Browser function.
Printing cannot be carried out and an error message appears
when jobs from other users (including other protocols) are
being printed.
OkiLAN 8300e Network User’s Guide
Microsoft Windows - 96
Novell NetWare
Overview
The OkiLAN print server supports the Novell NetWare environment.
It is necessary to have NetWare Administrator or Supervisor rights
to change the configuration. This guide is for NetWare
administrators. It should be read in conjunction with the relevant
Novell NetWare manual. The latest Novell service packs and Novell
client versions should be installed.
Supported Versions and Modes
NetWare 3.11 +
NetWare 4.1+
NetWare 5+
NetWare 6
Bindery
Bindery and NDS
Bindery, NDS and NDPS
Bindery, NDS, NDPS and iPrint
In NDS, the printer can be configured to work in either print server
mode or remote printer mode.
Remote Printer Mode
Remote Printer Mode requires a connection to be made to a
workstation running Pserver. Print jobs are received from the file
server via the NetWare print server. The network interface card
emulates the workstation on which the NetWare Rprinter operates.
Remote Printer Mode adds additional traffic to the network and is
slower than Print Server Mode but does not require any additional
licenses.
Print Server Mode (Recommended)
In Print Server Mode, the file server is logged in and the printer
queue is repeatedly polled to determine whether a print job exists.
The NetWare print server or workstation where Pserver runs is
emulated. This enables high speed printing without applying a load
to the network. Print Server Mode requires a single user NetWare
license.
OkiLAN 8300e Network User’s Guide
Novell NetWare - 97
Printing the Network Interface Card Configuration Sheet
The printer’s configuration page reports information that is
required for NetWare configuration. To print a configuration page,
while the printer is switched on, depress the NIC’s push-button for
two seconds and then release.
The Ethernet address (MAC Address) of the printer can be found on
the self-diagnostic printout, which can be printed by pressing the
push-button on the network card for two seconds and then
releasing it.
The first six digits of the Ethernet address are the same for all
OkiLan print servers. The last six digits of the Ethernet address are
unique to each card
This is all the information that is required to setup the OkiLan for
NetWare.
OkiLAN 8300e Network User’s Guide
Novell NetWare - 98
Setup Utilities
Use NWAdmin32 or the Pconsole utility to create and setup
NetWare printer objects. Please refer to Novell documentation for
instructions on how to achieve this.
Use the OKI Network Card Setup Utility (Quick Setup) or other
printer manager software, (AdminManager, Web browser, etc.) to
configure the network interface card. For instructions please refer
to the Configuration Utility section and online help. Below is the
NetWare configuration page from AdminManager.
Netware1.tif
OkiLAN 8300e Network User’s Guide
Novell NetWare - 99
UNIX
Overview
The OkiLAN print server supports many protocols such as LPD, FTP,
TELNET, SNMP and IPP, and works within the UNIX environment.
To use the network card within the UNIX environment, the
following steps are required:
Configuration
Network Interface card setting
The first step in installing the network card under UNIX is to set up
the IP address, Subnet Mask and Gateway. This section explains
one way to set them up from a UNIX workstation.
>
The network addresses used in this manual are shown as
examples only. Network addresses used in your installation
must be generated for your own network.
>
>
Log in as [root] to change the configuration of the Print
Server. By default, there is no root password.
If an incorrect IP address, Subnet Mask or Gateway is
entered, the network may go down or other damage may
occur. Check the address with your network manager.
The following explanation uses Sun Solaris 2.8 (Solaris 8) as an
example. The actual commands may differ between versions of
UNIX, so refer to the workstation manuals for more information.
1. Log in as root to the workstation
If you do not have superuser rights, the network manger
should conduct the configuration.
2. If the print server does not have an IP addresses already
assigned, use the arp command to set a temporary IP
address.
OkiLAN 8300e Network User’s Guide
UNIX - 100
Example: for IP address 172.68.20.127 and network card
address 00:80:92:01:00:D2
# arp –s 172.168.20.127 00:80:92:01:00:D2 temp
The Ethernet address (MAC address) 00:80:92:01:00:D2 in
the above example can be determined from the network card
self-diagnostic test which can be printed by pressing the
push-button on the network card for two seconds and then
releasing it.
3. Use the ping command to confirm the connection with the
network interface card.
Example: for IP address 172.168.20.127
# ping 172.168.20.127
If there is no reply, there is a problem with the configuration
of the IP address (the IP address has been already set
manually or by the DHCP/RARP server), or with the network.
Reset the network interface card settings to default and try
to set temporary IP address.
If you still have the problem after resetting the network
interface card, consult the network manager.
4. Log in to the network interface card using TELNET.
Example: Logging in to IP address 172.168.20.127
#telnet 172.168.20.127
Trying 172.168.20.127
Connected to 172.168.20.127
Escape character is ‘^]’.
EthernetBoard OkiLAN
OkiLAN 8300e Network User’s Guide
UNIX - 101
login: root
‘root’ user needs password to login.
password: <CR>
User ‘root’ logged in.
No. Message Value (level .1)
1 : Setup TCP/ IP
2 : Setup SNMP
3 : Setup NetWare
4 : Setup EtherTalk
5 : Setup NetBEUI
6 : Setup printer port
7 : Display Status
8 : Setup printer trap
9 : Setup SMTP Email
97 : Reset to factory set
98 : Quit setup
99 : Exit setup
Please select (1- 99)?
5. Type 1 and press the [Enter] key. Perform the following
settings:
Please select (1- 99)? 1
OkiLAN 8300e Network User’s Guide
UNIX - 102
No. Message Value
1 : TCP/ IP protocol : ENABLE
2 : IP address : 172.168.20.127
3 : Subnet Mask : 255.255.255.0
4 : Gateway address : 172.168.20.1
5 : RARP protocol : DISABLE
6 : DHCP/ BOOTP protocol: DISABLE
7 : root password : “ “
99 : Back to prior menu
Please select (1- 99)?
6. Log out from the network interface card. Turn the printer off
and on again to validate the following settings.
OkiLAN 8300e Network User’s Guide
UNIX - 103
Operating system configuration
This section explains how to configure a printer for major UNIX
operating systems.
Sun OS 4.x.x (BSD) configuration
The following explanation uses Sun OS 4.1.3 and an OKI printer as
examples. The absolute path of commands and the configuration
method may differ between OS versions, so refer to the
workstation manuals for more information.
If an incorrect IP Address, Subnet Mask or Gateway is entered, the
network may go down or other damage may occur. Check the
address with the network manager and confirm that the IP address
of the printer has been set.
1. Log in as root to the workstation.
If you do not have Superuser rights, the network manager
should conduct the configuration.
2. Register the IP address of the network card and the host
name in the /etc/hosts file.
Example: for IP address 172.168.20.127 and host name
PRINTER
172.168.20.127 PRINTER
3. Use the ping command to confirm connection with the
network card.
Example: for host name PRINTER
# ping PRINTER
If there is no reply, then there is a problem with the
configuration of the IP address (the IP address has been
already set manually or by the DHCP/RARP server) or with
OkiLAN 8300e Network User’s Guide
UNIX - 104
the network. Reset the network interface card settings to
their defaults and then try to set a temporary IP address. If
you still have the problem after resetting the network
interface card, consult the network manager.
4. Register the printer in the /etc/printcap file.
Example: for host name PRINTER, to create a queue called
PRINTER_lp
PRINTER_lp: \
:lp=:rm=C7400:rp=lp:\
:sd=/usr/spool/PRINTER_lp:\
:lf=/usr/spool/PRINTER_lp/OKIPRINTER_lp_errs:
PRINTER_lp The name of the printer queue
lp: The name of the device used to connect to the printer.
Does not need to be specified for a remote machine.
rm: The name of the host of the remote printer. This should
be the same as the name added to the /etc/hosts file.
rp: The name of the printer on the remote printer. It should
be lp.
sd: The spool directory. Give the absolute path.
lf: The error log file. Give the absolute path.
5. Create the spool directory and error log file.
Example: for spool Directory PRINTER_lp and Error Log file
OKIPRINTER_lp_errs
# mkdir /usr/spool/PRINTER_lp
#touch/usr/spool/PRINTER_lp/PRINTER _lp_errs
OkiLAN 8300e Network User’s Guide
UNIX - 105
# chown –R daemon /usr/spool/PRINTER_lp
# chgrp –R # daemon /usr/spool/PRINTER_lp
6. Check that lpd (printer daemon) is activated.
# ps aux | grep lpd
7. If lpd is not running,start it by logging in as superuser and
executing
# /usr/lib/lpd &
Sun Solaris 2.x configuration
Admintool is normally used to register remote printers on Open
Windows. However, it cannot be used here, as the data recipient
and queue have the same name. The procedure below must be
used for registering a remote printer.
If Solaris 2.x is connected to the remote printer for a long period
according to the system specifications, errors and forced
disconnection may occur. Therefore, if paper tearing, off-line and
other errors result in waiting time, printing may have to be
aborted.
If an incorrect IP address is entered, the network may go down or
other damage may occur. Configure after consulting the network
manager.
The following explanation uses Sun Solaris 2.8 (known as Solaris
8) and an OKI printer as examples. The absolute path and method
of configuring commands may differ in other versions of the OS.
Refer to the workstation manual for more details.
1. Confirm that the IP address of the printer has been set.
2. Log in as [root] to the workstation. If you do not have
superuser rights, the network manager should conduct the
configuration.
OkiLAN 8300e Network User’s Guide
UNIX - 106
3. Register the IP address of the network card and the host
name in /etc/hosts file.
Example: for IP Address 172.168.20.127 and host name
PRINTER
172.168.20.127PRINTER
4. Use the ping command to confirm connection with the
network card.
Example: for host name PRINTER
# ping PRINTER
If there is no reply, there is a problem with the configuration
of the IP address (the IP address has been already set
manually or by the DHCP/RARP server), or with the network.
Reset the network interface card settings to default and try
to set temporary IP address. If you still have the problem
after resetting the network interface card, consult the
network manager.
5. Register the network card as a remote printer server.
Example: for host name PRINTER
a. Stop the print scheduler.
# usr/sbin/lpshut
b. Create the printer queue.
# /usr/sbin/lpadmin -p PRINTER_lp -v /dev/null \
m netstandard -o dest=PRINTER:lp
-o protocol=bsd
c. Set the queue to accept PostScript print jobs.
OkiLAN 8300e Network User’s Guide
UNIX - 107
# /usr/sbin/lpadmin -p PRINTER_lp -I postscript
d. Start the print scheduler.
# /usr/sbin/lpsched
e. Activate the print queue.
# /usr/sbin/accept PRINTER_lp
f.
Enable the print queue
# /bin/enable PRINTER_lp
To customize output, for example to add additional commands at
the start of each print job, you can edit a copy of the netstandard
model file then add it using the lpadmin command
Example: for printer PRINTER_lp, with model file called
PRINTER0_model
# /usr/sbin/lpshut
# /usr/sbin/lpadmin –p PRINTER_lp –m
PRINTER_model
# /usr/sbin/lpsched
HP-UX 10.x configuration
If an incorrect IP Address, Subnet Mask or Gateway is entered, the
network may go down or other damage may occur. Check the
address with the network manager.
The following example uses HP-UX10.20 and an OKI printer as
examples. The absolute path and method of configuring commands
may differ in other versions of the OS. Refer to the workstation
manual for more details.
1. Confirm that the IP address of the printer has been set. See
network interface card IP address configuration for more
information.
OkiLAN 8300e Network User’s Guide
UNIX - 108
2. Log in as [root] to the workstation. If you do not have
superuser rights, the network manager should conduct the
configuration.
3. Register the IP Address of the network card and the host
name in the /etc/hosts file.
Example: for IP Address 172.168.20.127 and host name
PRINTER
172.168.20.127 PRINTER
4. Use the ping command to confirm connection with the
network card.
Example: for host name PRINTER
# ping PRINTER
If there is no reply, there is a problem with the configuration
of the IP address (the IP address has been already set
manually or by the DHCP/RARP server), or with the network.
Reset the network interface card settings to default and try
to set a temporary IP address. If you still have the problem
after resetting the network interface card, consult the
network manager.
5. If remote spooling is not already enabled on the HP-UX
machine, carry out the following configuration.
a. Stop the printer spooler.
# /usr/sbin/lpshut
b. Add the following line to the /etc/inetd.conf file and
register the remote spooler.
printer stream tcp nowait root /usr/sbin/rlpdameon –I
c. Restart inetd
OkiLAN 8300e Network User’s Guide
UNIX - 109
# /etc/inetd –c
4. Register the remote printer
Example: setting up a queue called PRINTER_lp to print to
host PRINTER
a. Register the remote printer.
# /usr/sbin/lpadmin -pPRINTER_lp -v /dev/null
-mrmodel \-ormPRINTER -orplp -ocmrcmodel
-osmrsmodel -ob3
b. Activate the print queue.
# /usr/sbin/accept PRINTER_lp
c. Enable the print queue.
# /bin/enable PRINTER_lp
d. Enable the printer spooler.
# /usr/sbin/lpsched
To customise output, for example, to add additional commands at
the start of each print job, you can edit a copy of the /usr/spool/
lp/model/rmodel model file then add it using the lpadmin
command.
Example: for printer PRINTER_lp, with model file called
PRINTER_model
# /usr/sbin/lpshut
# /usr/sbin/lpadmin –pPRINTER_lp –
mPRINTER_model
# /usr/sbin/lpsched
OkiLAN 8300e Network User’s Guide
UNIX - 110
AIX 4.1.5 configuration
The following explanation uses AIX4.1.5 and an OKI printer as
examples. The absolute path of commands and the method of
configuring may differ with the OS version. Refer to the
workstation’s manual. If an incorrect IP address is entered, the
network may go down or other damage may occur. Configure after
consulting the network manager.
1. Log in as [root]. If you do not have superuser rights, the
network manager should conduct the configuration.
2. Register the IP address and the host name in the /etc/hosts
file.
Example: for IP Address 172.168.29.127 and host name
okiprinter
172.168.20.127 PRINTER
3. Use the ping command to confirm connection with the
network card.
Example: for host name okiprinter
# ping PRINTER
If there is no reply, there is a problem with the configuration of the
IP address (the IP address has been already set manually or by the
DHCP/RARP server), or with the network. Reset the network
interface card settings to default and try to set a temporary IP
address. If you still have the problem after resetting the network
interface card, consult the network manager.
4. Register the host that was previously registered as the print
server.
Example: for the OKI printer registered as the print server
a. Add the print server.
# ruser –a –p okiprinter
OkiLAN 8300e Network User’s Guide
UNIX - 111
b. Activate the remote printer daemon.
# startsrc –s lpd
# mkitab ‘lpd:2:once:startsrc –s lpd’
3. Add the print queue using the smit command.
a. Activate the smit command and convert to the item
[Add print queue].
# smit mkrque
b. Select [remote] (the printer connected to the remote
host) from [Type of connection].
c. Select [Standard procedure] from Type of remote print.
d. Carry out the following settings in [Add a standard
remote print queue]. If the configuration differs from
below, configure according to environment.
Example: fr direct output port lp with print queue
okiprinte_lp and print server okiprinte
Queue to be added
Host name of the
“printer_lp”
“printer”
“lp”
remote server
Queue name of the
remote server
Type of print spooler
of the remote server
Description of printer name
“BSD”
OkiLAN 8300e Network User’s Guide
UNIX - 112
of the remote server
LPD Printing
“Optional comment”
Line Printer Daemon (LPD) is the most common protocol for
printing with TCP/IP to a network printer. Refer to the
workstation’s manual for details of lpr and lp commands. The
following explanation in this section uses the printing of print file
test.prn with printer name PRINTER_lp as an example.
Logical printers
The OkiLAN print server includes three logical printers.
>
>
>
lp must be used for printing a file created using the printer
driver.
sjis must be used for printing a text file of Shift JIS Kanji
code.
euc must be used for the printing a text file of the EUC Kanji
code.
Logical printer
Printer function
lp
For direct output
sjis
euc
For Shift JIS Kanji converted output
For EUC Kanji converted output
>
sjis and euc function only as PostScript printers.
BSD-based UNIX
Print using the lpr command.
# lpr –PCprinter_lp test.prn
If the lprm command is used, the print job is cancelled.
Example: To delete a print job (Job ID 123) on the
okiprinter_lp
OkiLAN 8300e Network User’s Guide
UNIX - 113
# lprm –PCprinter_lp 123
Verify the printer status using the lpq command.
>
The result of lpq may not be displayed correctly depending on
UNIX operating system specification.
>
While the short format of lpq is a UNIX compatible format, the
long format is unique to the OkiLAN print server.
Example of the short format: # lpq –PCprinter_lp
Example of the long format: # lpq –l -PCprinter_lp
System V-based UNIX
Print using the lp command.
# lp –d Cprinter_lp test.prn
Delete a print job using cancel command.
Example: To delete a print job (Job ID 456) in the printer_lp
# cancel Cprinter_lp -456
Verify the printer status using the lpstat command.
# lpstat –pCprinter_lp
>
The result of lpstat may not be displayed correctly depending
on UNIX operating system specification (e.g. Solaris 2.x).
FTP printing
FTP (File Transfer Protocol) is used for transferring a file with TCP/
IP. If the print data is sent to a logical printer via FTP, it is printed.
Refer to the workstation’s manual for details of the ftp command.
The following explanation uses print file test.prn with printer name
okiprinter_lp as an example.
OkiLAN 8300e Network User’s Guide
UNIX - 114
Logical directories
The OkiLAN print server includes three logical directories.
lp must be used for printing a file created using the printer
driver.
sjis must be used for printing a text file of Shift JIS Kanji
code.
euc must be used for the printing a text file of the EUC Kanji
code
Logical directory
Printer function
lp
For direct output
sjis
euc
For Shift JIS Kanji converted output
For EUC Kanji converted output
>
>
jis and euc function only as PostScript printers.
You can not send data to the root directory.
1. Login to the network interface card.
When printing with ftp, use any values for name and
password. However, if the user name is [root], the password
set under TELNET or the utility are required. See the
appropriate section for details.
Example: Logging in with host name printer (or IP address
172.168.20.127).
# ftp printer (or ftp 172.168.20.127
Connected to Cprinter
220 EthernetBoard OkiLAN Ver 1.1.0 FTP Server
Name (Cprinter:root) :
root
OkiLAN 8300e Network User’s Guide
UNIX - 115
331 Password required.
Password:<CR>
230 User Logged in
ftp>
The network card logical directory structure is hierarchical.
Move to the logical directory; it is not possible to output print
data to the root directory.
2. Move to the preferable logical directory using the cd
command.
Example: moving to the lp directory and confirming the
current directory.
ftp> cd /lp
250 Command OK.
ftp> pwd
257 ”/lp” is current directory
ftp>
3. Configure the transfer mode
There are two types of transfer mode: BINARY mode, in
which the file contents are output as it is and ASCII mode,
which converts the LF code to the CR+LF code. If a binary file
converted by the printer driver is transferred, the transfer
mode has to be BINARY mode.
Example: changing transfer mode to binary mode and
verifying the current mode
ftp> type binary
OkiLAN 8300e Network User’s Guide
UNIX - 116
200 Type set to I.
ftp> type
Using binary mode to transfer files.
ftp>
4. Transfer the print data to the network card using the put
command. Two methods of file transfer using the put
command are available.
Example: transferring print data test.prn
ftp> put test.prn
Example: transferring print data specified by absolute path/
users/test/test.prn
ftp> put /users/test/test.prn /lp
5. Logout from the network card using the quit command
ftp> quit
Three states can be verified using the quote command stat:
the IP address, login user name and transfer mode. In
addition, printer status can be verified by specifying the
directory after the stat (lp, sjis, euc).
Example: displaying network card status
ftp> quote stat
211-FTP server status:
Connected to: 172.168.20.10.000.00
User logged in: root
Transfer type: BINARY
OkiLAN 8300e Network User’s Guide
UNIX - 117
Data connection: Closed.
211 End of status.
ftp>
Example: displaying the network card status (directory
name: lp)
ftp> quote stat /lp
211-FTP directory status:
Ready
211 End of status
ftp>
OkiLAN 8300e Network User’s Guide
UNIX - 118
®
®
Apple Macintosh
Overview
The OkiLAN print server supports the Apple Macintosh AppleTalk
environment. This guide is for administrators and it should be read
in conjunction with the relevant Macintosh manual. The latest
Macintosh service packs should be installed.
Supported Versions
Mac OS X.1 and forward are supported.
Printing the Network Interface Card Configuration
Sheet
The printer’s configuration page reports information that is
required for Macintosh configuration. To print a configuration page,
while the printer is switched on, depress the NIC’s push-button for
two seconds and then release.
The information that you require is the printer’s Ethernet address
(MAC address). It is displayed at the top of the first page under the
title General Information.
The first six digits of the Ethernet address are the same for all
OkiLAN print servers. The last six digits of the Ethernet address
are unique to each card.
This is all the information that is required to setup the OkiLAN print
server for Macintosh.
OkiLAN 8300e Network User’s Guide
Apple® Macintosh® - 119
Installation
Install the Driver
1. Place the CD, supplied with your printer, in the CD-ROM
drive.
2. Double-click the icon that appears on the desktop.
3. Open the MAC folder.
4. Double-click the Printer Installer icon, click Continue.
5. Installer displays with the driver selected.
6. Select any utilities you want to install. Click Install.
OkiLAN 8300e Network User’s Guide
Apple® Macintosh® - 120
Macintosh Printer Setup
OS X.1 and above
In Mac OS X you use the Print Center to setup network printers.
1. Run the Print Server or Print Setup Utility.
2. Select OKI TCP/IP from the drop-down menu.
3. Enter the printer IP address.
4. From the Printer Model drop down menu, select your printer
model.
5. Click Add.
6. Quit the Print Center.
OkiLAN 8300e Network User’s Guide
Apple® Macintosh® - 121
Troubleshooting
The network addresses used in this manual are shown for example
only. Network addresses used in your installation must be
generated from your own network.
Self-diagnostic test
Printer does not print.
Ensure the printer emulation is set to PS (if available) or
Automatic.
NG is printed in the Self-diagnostic test.
Confirm that the NIC is installed correctly in models that require an
optional NIC card and turn the printer off and on again.
Ensure the network cable is correctly connected and connect to a
different network segment, rerun the test and see if this cures the
fault.
EEPROM Check registers NG.
Confirm that the NIC is installed correctly and turn the printer off
and on again.
Initialize the NIC.
TCP/IP
Printer cannot find the network interface card.
Turn the printer off and on again.
Confirm the network interface is enabled on the printer.
Check there is a response to the interface card command.
Check the network cable is correctly connected.
OkiLAN 8300e Network User’s Guide
Troubleshooting - 122
Change the cable and try again.
Run the Self-diagnostic test.
Check the IP Address, Subnet Mask and Gateway are correct.
Check that the TCP/IP protocol is set to Enable.
Reset the network interface card to factory default settings.
If DHCP, BOOTP and RARP are not used, ensure they have been set
to Disable.
Cannot print with lpr and ftp.
Turn the printer off and on again.
Check there is a response to the ping command.
Check the network cable is correctly connected.
Change the cable and try again.
Check the host name and IP address are configured in the
workstation.
Check the printer port name is configured in the workstation.
There are three port names: lp, euc and sjis. Use lp by default as
euc and sjis are specific to printers with PostScript available.
Incorrect User name on the banner page.
If printing with lpr, the User name printed is unknown and the
Filename printed is the Spool file name.
If printing with FTP, the User name printed is the User name
entered during FTP login and the File name printed is the
Transmitted file name. If the Print Directory name is indicated in
the put command, the File name is not printed. The Printer name
printed is the Logical Directory name.
OkiLAN 8300e Network User’s Guide
Troubleshooting - 123
NetWare
Printer cannot find the network print server.
Turn the printer off and on again.
Confirm the network interface is enabled on the printer.
Check the network cable is correctly connected.
Change the cable and try again.
If the standard configuration utility is used, check the NetWare
network number in the environment settings.
If the NetWare protocol is disabled, set it to Enable.
Reset the network interface card to factory default settings.
The network print server is identified by the setup utility but not by
the NetWare server.
Start up the NetWare server and check the NIC configuration.
Check the NSAP packet on the NetWare server is not set to Disable.
Remote Server mode
Check the correct print server is operating on the file server.
Check the Print Server name operating on the File Server and the
Print Server name set in the NIC are the same.
Check the Printer name displayed in the Print Server monitor of the
File Server and the NetWare Port name set in the NIC are the same.
If there are multiple network interface cards, configure the
NetWare Port names to be different.
OkiLAN 8300e Network User’s Guide
Troubleshooting - 124
Print Server mode
Check the File Server name set in the NIC and on the File Server
are the same.
Check the Printer name set in the File Server and the NetWare Port
name set in the NIC are the same. If there are multiple NICs,
configure the NetWare Port names to be different.
Check the NetWare login password is correct.
Check the Machine name is the same as the Print Server name set
in the File Server.
Printer does not print.
Check the network cable is correctly connected.
Change the cable and try again.
Turn the printer off and on again.
Check the NIC is connected to the File Server.
Check the printer driver has been mapped to the correct
netware queue.
PostScript error occurs if a Banner Page is printed.
A PostScript Banner page cannot be printed in NetWare 3.12
Remote Printer mode. If a PostScript printer is used and a
Banner Page is printed, PostScript error is displayed. Turn
the banner output Off in the client’s printer settings.
OkiLAN 8300e Network User’s Guide
Troubleshooting - 125
EtherTalk
Not identified by the Chooser and the Setup Utility.
Turn the printer off and on again.
Check the network cable is correctly connected.
Change the cable and try again.
If the network resides in a Zone, check the correct Zone name is
selected in the Chooser.
Check the Zone name in the utility related to the NIC is the same
as the Zone name set in NIC.
Check AppleTalk, which is displayed at the right bottom of the
Chooser, is set to Enable. (In some OS versions Network is used
instead of AppleTalk.)
Check Ethernet is selected in AppleTalk. (In some OS versions
Network is used instead of AppleTalk.)
Check the print driver is selected in the Chooser.
Check the EtherTalk protocol is set to Enable.
Print the NIC settings and confirm that the EtherTalk Port name is
not blank.
OkiLAN 8300e Network User’s Guide
Troubleshooting - 126
NetBEUI
The network interface card is not identified.
Turn the printer off and on again.
Check the network cable is correctly connected.
Change the cable and try again.
Check Microsoft network client and NetBEUI have been added to
the network section of the control panel.
Check the NetBEUI protocol is set to Enable.
Check the factory setting of the workgroup name is PrintServer and
the computer name is ML+ the last six digits of the MAC address.
Check the computer name of the NIC is different from the
computer name on the network.
Error writing to Prn1.
Check the printer is online.
If there is an error message indicating the paper has run out, add
more paper and cancel the error.
Check whether another user is printing. Print after the other user
has finished.
OkiLAN 8300e Network User’s Guide
Troubleshooting - 127
Oki Data Americas, Inc.
2000 Bishops Gate Blvd., Mt. Laurel, NJ 08054-4620
Tel: (856)235-2600
Fax: (856)222-5320
59385005
|